summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2016-09-09squelch errors from netcat when it needs to start oocdKarl Palsson1-2/+2
be nice if I could _keep_ errors when V=1 but....
2016-08-19rcc-legal-ranges: run through a range of clocksKarl Palsson3-30/+119
blink fast/slow for each clock configuration tested, then finish by blinking idly. As of this commit, this test fails quickly on most L1 boards tested. An update to libopencm3 is required to fix this.
2016-08-19Update libopencm3 to latestKarl Palsson1-0/+0
2016-08-18rcc-legal-ranges: initial l1 setupKarl Palsson3-0/+107
Doesn't fail on my l1 disco unfortunately. (silicon rev X) Does fail on a custom board with silicon rev V
2016-08-18Update libopencm3 to current masterKarl Palsson1-0/+0
2016-03-30adc: hacks to get it up and running for L4Karl Palsson2-3/+15
2016-03-30adc: document where debug output goesKarl Palsson1-0/+4
2016-03-30rules: attempt to connect to a running openocd first.Karl Palsson1-2/+4
2016-03-30adc: use single float literalsKarl Palsson1-3/+3
Dramatic performance improvement on m4f cores, ~1600->80 cycles
2016-03-30adc: f4: update for new namingKarl Palsson1-1/+1
2016-03-14update modulsKarl Palsson1-0/+0
2016-03-14fix l4 to run at 48Mhz and with a clockKarl Palsson3-2/+14
2016-03-04update library submoduleKarl Palsson1-0/+0
2016-03-04attempt actual adc on l4Karl Palsson3-5/+23
(insufficient,needs clocks yet)
2016-03-04f3: use new rcc namesKarl Palsson1-8/+11
2016-03-04use new names for SMPRx definesKarl Palsson1-2/+6
2016-03-04fix path to common f0 oocd fileKarl Palsson1-1/+1
2016-03-04l4 miniblinkKarl Palsson3-0/+89
We'll build up to the adc temp sensor from here
2016-03-04f0 working (one fixme)Karl Palsson6-3/+146
need scan mode upstream?
2015-11-03WIP: f0 adc buildKarl Palsson1-1/+11
2015-11-03f3 temp sensor workingKarl Palsson3-10/+15
2015-11-03f4: proper float/int temp readingsKarl Palsson3-41/+50
2015-10-28gitignore projects, bins and dump logsKarl Palsson1-0/+7
2015-10-28f3: wip continuesKarl Palsson2-14/+131
2015-10-19openocd: correct f3 serial numberKarl Palsson1-1/+1
After upgrading and verifying.
2015-10-17WIP: adc-power f3Karl Palsson3-0/+93
needs rcc fixups
2015-10-17adc-power: f4: use correct path to linkerKarl Palsson1-1/+1
Don't escape the project!
2015-10-17fix markdownKarl Palsson1-5/+5
2015-10-17stub adc on/off test code.Karl Palsson8-0/+502
Needs a pot on PA0, should get the temperature input working as well.
2015-10-16initial openocd config filesKarl Palsson2-0/+16
2015-10-16add libopencm3 as submoduleKarl Palsson2-0/+3
2015-10-16purpose of first testKarl Palsson1-0/+8
2015-10-16purpose of shared directoryKarl Palsson1-0/+2
2015-10-16Initial commitKarl Palsson2-0/+29