3 files changed, 175 insertions, 0 deletions
diff --git a/tests/spi-master/Makefile b/tests/spi-master/Makefile
new file mode 100644
index 0000000..52841cd
--- /dev/null
+++ b/tests/spi-master/Makefile
@@ -0,0 +1,15 @@
+# This is just a stub makefile used for travis builds
+# to keep things all compiling. Normally you'd use
+# one of the makefiles directly.
+
+# These hoops are to enable parallel make correctly.
+GZ_ALL := $(wildcard Makefile.*)
+
+all: $(GZ_ALL:=.all)
+clean: $(GZ_ALL:=.clean)
+
+%.all:
+	make -f $* all
+%.clean:
+	make -f $* clean
+	
diff --git a/tests/spi-master/Makefile.dut-stm32l073rz b/tests/spi-master/Makefile.dut-stm32l073rz
new file mode 100644
index 0000000..899c0fe
--- /dev/null
+++ b/tests/spi-master/Makefile.dut-stm32l073rz
@@ -0,0 +1,21 @@
+BOARD = dut-stm32l073rz
+PROJECT = spi-master-$(BOARD)
+BUILD_DIR = bin-$(BOARD)
+
+SHARED_DIR = ../../shared
+
+CFLAGS = -DSTDIO_USART=USART2
+CFILES = main-$(BOARD).c
+#CFILES += spi-master.c
+# No trace on cm0!
+#CFILES += trace.c trace_stdio.c
+CFILES += usart_stdio.c
+
+VPATH += $(SHARED_DIR)
+
+INCLUDES += $(patsubst %,-I%, . $(SHARED_DIR))
+
+OPENCM3_DIR=../../libopencm3
+DEVICE=stm32l073rz
+OOCD_FILE = openocd.dut-stm32l073rz.cfg
+include ../../rules.mk
diff --git a/tests/spi-master/main-dut-stm32l073rz.c b/tests/spi-master/main-dut-stm32l073rz.c
new file mode 100644
index 0000000..63898d5
--- /dev/null
+++ b/tests/spi-master/main-dut-stm32l073rz.c
@@ -0,0 +1,139 @@
+/*
+ * March 2017 Karl Palsson <karlp@tweak.net.au>
+ */
+
+#include <errno.h>
+#include <stdio.h>
+#include <unistd.h>
+#include <libopencm3/cm3/nvic.h>
+#include <libopencm3/stm32/gpio.h>
+#include <libopencm3/stm32/rcc.h>
+#include <libopencm3/stm32/spi.h>
+#include <libopencm3/stm32/usart.h>
+
+#include "hw.h"
+
+#define LED_DISCO_GREEN_PORT GPIOB  // actually cs
+#define LED_DISCO_GREEN_PIN GPIO6
+
+
+struct hw_detail hw_details = {
+	.periph = SPI1,
+	.periph_rcc = RCC_SPI1,
+	.periph_rst = RST_SPI1,
+	.pins = GPIO5| GPIO6 | GPIO7, /* SPI pins for setting AF with */
+	.port = GPIOA,
+	.port_rcc = RCC_GPIOA,
+	.trigger_rcc = RCC_GPIOB,
+	.trigger_port = GPIOB,
+	.trigger_pin = GPIO8,   // pb6 is d7 on the LA
+};
+
+
+/* provided in board files please*/
+/**
+ * Setup any gpios or anything hardware specific.
+ * Should _only_ be things that can't be done in shared init()
+ */
+static void hw_init(void)
+{
+	/* trigger pin gpio */
+	rcc_periph_clock_enable(hw_details.trigger_rcc);
+	gpio_mode_setup(hw_details.trigger_port, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, hw_details.trigger_pin);
+
+	/* spi control lines */
+	rcc_periph_clock_enable(hw_details.port_rcc);
+	gpio_mode_setup(hw_details.port, GPIO_MODE_AF, GPIO_PUPD_NONE, hw_details.pins);
+	gpio_set_output_options(hw_details.port, GPIO_OTYPE_PP, GPIO_OSPEED_MED, hw_details.pins);
+	gpio_set_af(hw_details.port, GPIO_AF0, hw_details.pins);
+}
+
+static void test_init(void)
+{
+        /* Setup SPI parameters. */
+	rcc_periph_clock_enable(hw_details.periph_rcc);
+        spi_init_master(hw_details.periph, SPI_CR1_BAUDRATE_FPCLK_DIV_64, SPI_CR1_CPOL_CLK_TO_0_WHEN_IDLE,
+                SPI_CR1_CPHA_CLK_TRANSITION_1, SPI_CR1_DFF_8BIT, SPI_CR1_MSBFIRST);
+        /* Ignore the stupid NSS pin. */
+        spi_enable_software_slave_management(hw_details.periph);
+        spi_set_nss_high(hw_details.periph);
+
+        /* Finally enable the SPI. */
+        spi_enable(hw_details.periph);
+}
+
+static void test_task(void) {
+	static int i = 0;
+	gpio_set(hw_details.trigger_port, hw_details.trigger_pin);
+	printf("Test iteration %d\n", i++);
+	spi_xfer(hw_details.periph, 0xaa);
+	spi_xfer(hw_details.periph, 0x42);
+	spi_xfer(hw_details.periph, 0x69);
+
+	gpio_clear(hw_details.trigger_port, hw_details.trigger_pin);
+}
+
+static
+void setup_usart(void)
+{
+        uint32_t dev = USART2;
+        rcc_periph_clock_enable(RCC_USART2);
+        rcc_periph_clock_enable(RCC_GPIOA);
+        gpio_mode_setup(GPIOA, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO2|GPIO3);
+        gpio_set_af(GPIOA, GPIO_AF4, GPIO2|GPIO3);
+
+        usart_set_baudrate(dev, 115200);
+        usart_set_databits(dev, 8);
+        usart_set_parity(dev, USART_PARITY_NONE);
+        usart_set_stopbits(dev, USART_STOPBITS_1);
+        usart_set_mode(dev, USART_MODE_TX_RX);
+        usart_set_flow_control(dev, USART_FLOWCONTROL_NONE);
+
+        /* Finally enable the USART. */
+        usart_enable(dev);
+}
+
+
+static void setup(void)
+{
+	setup_usart();
+	printf("hi guys!\n");
+	hw_init();
+	test_init();
+}
+
+
+int main(void)
+{
+	const struct rcc_clock_scale myclock = {
+		.pll_source = RCC_CFGR_PLLSRC_HSI16_CLK,
+		.pll_mul = RCC_CFGR_PLLMUL_MUL4,
+		.pll_div = RCC_CFGR_PLLDIV_DIV2,
+		.hpre = RCC_CFGR_HPRE_NODIV,
+		.ppre1 = RCC_CFGR_PPRE1_NODIV,
+		.ppre2 = RCC_CFGR_PPRE2_NODIV,
+		.voltage_scale = PWR_SCALE1,
+		.flash_waitstates = 1,
+		.ahb_frequency = 32e6,
+		.apb1_frequency = 32e6,
+		.apb2_frequency = 32e6,
+	};
+	int i, j;
+	rcc_clock_setup_pll(&myclock);
+        rcc_periph_clock_enable(RCC_SYSCFG);
+
+	/* green led for ticking */
+	rcc_periph_clock_enable(RCC_GPIOB);
+	gpio_mode_setup(LED_DISCO_GREEN_PORT, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, LED_DISCO_GREEN_PIN);
+	gpio_set(LED_DISCO_GREEN_PORT, LED_DISCO_GREEN_PIN);
+	setup();
+
+	while (1) {
+		test_task();
+		//gpio_toggle(LED_DISCO_GREEN_PORT, LED_DISCO_GREEN_PIN);
+		for (i = 0; i < 0x80000; i++) { /* Wait a bit. */
+                        __asm__("NOP");
+                }
+	}
+	return 0;
+}