diff options
Diffstat (limited to 'fw/hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_smbus.c')
| -rw-r--r-- | fw/hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_smbus.c | 2673 |
1 files changed, 0 insertions, 2673 deletions
diff --git a/fw/hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_smbus.c b/fw/hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_smbus.c deleted file mode 100644 index cbf6689..0000000 --- a/fw/hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_smbus.c +++ /dev/null @@ -1,2673 +0,0 @@ -/**
- ******************************************************************************
- * @file stm32f0xx_hal_smbus.c
- * @author MCD Application Team
- * @brief SMBUS HAL module driver.
- * This file provides firmware functions to manage the following
- * functionalities of the System Management Bus (SMBus) peripheral,
- * based on I2C principles of operation :
- * + Initialization and de-initialization functions
- * + IO operation functions
- * + Peripheral State and Errors functions
- *
- @verbatim
- ==============================================================================
- ##### How to use this driver #####
- ==============================================================================
- [..]
- The SMBUS HAL driver can be used as follows:
-
- (#) Declare a SMBUS_HandleTypeDef handle structure, for example:
- SMBUS_HandleTypeDef hsmbus;
-
- (#)Initialize the SMBUS low level resources by implementing the @ref HAL_SMBUS_MspInit() API:
- (##) Enable the SMBUSx interface clock
- (##) SMBUS pins configuration
- (+++) Enable the clock for the SMBUS GPIOs
- (+++) Configure SMBUS pins as alternate function open-drain
- (##) NVIC configuration if you need to use interrupt process
- (+++) Configure the SMBUSx interrupt priority
- (+++) Enable the NVIC SMBUS IRQ Channel
-
- (#) Configure the Communication Clock Timing, Bus Timeout, Own Address1, Master Addressing mode,
- Dual Addressing mode, Own Address2, Own Address2 Mask, General call, Nostretch mode,
- Peripheral mode and Packet Error Check mode in the hsmbus Init structure.
-
- (#) Initialize the SMBUS registers by calling the @ref HAL_SMBUS_Init() API:
- (++) These API's configures also the low level Hardware GPIO, CLOCK, CORTEX...etc)
- by calling the customized @ref HAL_SMBUS_MspInit(&hsmbus) API.
-
- (#) To check if target device is ready for communication, use the function @ref HAL_SMBUS_IsDeviceReady()
-
- (#) For SMBUS IO operations, only one mode of operations is available within this driver
-
- *** Interrupt mode IO operation ***
- ===================================
- [..]
- (+) Transmit in master/host SMBUS mode an amount of data in non-blocking mode using @ref HAL_SMBUS_Master_Transmit_IT()
- (++) At transmission end of transfer @ref HAL_SMBUS_MasterTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_MasterTxCpltCallback()
- (+) Receive in master/host SMBUS mode an amount of data in non-blocking mode using @ref HAL_SMBUS_Master_Receive_IT()
- (++) At reception end of transfer @ref HAL_SMBUS_MasterRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_MasterRxCpltCallback()
- (+) Abort a master/host SMBUS process communication with Interrupt using @ref HAL_SMBUS_Master_Abort_IT()
- (++) The associated previous transfer callback is called at the end of abort process
- (++) mean @ref HAL_SMBUS_MasterTxCpltCallback() in case of previous state was master transmit
- (++) mean @ref HAL_SMBUS_MasterRxCpltCallback() in case of previous state was master receive
- (+) Enable/disable the Address listen mode in slave/device or host/slave SMBUS mode
- using @ref HAL_SMBUS_EnableListen_IT() @ref HAL_SMBUS_DisableListen_IT()
- (++) When address slave/device SMBUS match, @ref HAL_SMBUS_AddrCallback() is executed and user can
- add his own code to check the Address Match Code and the transmission direction request by master/host (Write/Read).
- (++) At Listen mode end @ref HAL_SMBUS_ListenCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_ListenCpltCallback()
- (+) Transmit in slave/device SMBUS mode an amount of data in non-blocking mode using @ref HAL_SMBUS_Slave_Transmit_IT()
- (++) At transmission end of transfer @ref HAL_SMBUS_SlaveTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_SlaveTxCpltCallback()
- (+) Receive in slave/device SMBUS mode an amount of data in non-blocking mode using @ref HAL_SMBUS_Slave_Receive_IT()
- (++) At reception end of transfer @ref HAL_SMBUS_SlaveRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_SlaveRxCpltCallback()
- (+) Enable/Disable the SMBUS alert mode using @ref HAL_SMBUS_EnableAlert_IT() @ref HAL_SMBUS_DisableAlert_IT()
- (++) When SMBUS Alert is generated @ref HAL_SMBUS_ErrorCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_ErrorCallback()
- to check the Alert Error Code using function @ref HAL_SMBUS_GetError()
- (+) Get HAL state machine or error values using @ref HAL_SMBUS_GetState() or @ref HAL_SMBUS_GetError()
- (+) In case of transfer Error, @ref HAL_SMBUS_ErrorCallback() function is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_ErrorCallback()
- to check the Error Code using function @ref HAL_SMBUS_GetError()
-
- *** SMBUS HAL driver macros list ***
- ==================================
- [..]
- Below the list of most used macros in SMBUS HAL driver.
-
- (+) @ref __HAL_SMBUS_ENABLE: Enable the SMBUS peripheral
- (+) @ref __HAL_SMBUS_DISABLE: Disable the SMBUS peripheral
- (+) @ref __HAL_SMBUS_GET_FLAG: Check whether the specified SMBUS flag is set or not
- (+) @ref __HAL_SMBUS_CLEAR_FLAG: Clear the specified SMBUS pending flag
- (+) @ref __HAL_SMBUS_ENABLE_IT: Enable the specified SMBUS interrupt
- (+) @ref __HAL_SMBUS_DISABLE_IT: Disable the specified SMBUS interrupt
-
- *** Callback registration ***
- =============================================
- [..]
- The compilation flag USE_HAL_SMBUS_REGISTER_CALLBACKS when set to 1
- allows the user to configure dynamically the driver callbacks.
- Use Functions @ref HAL_SMBUS_RegisterCallback() or @ref HAL_SMBUS_RegisterAddrCallback()
- to register an interrupt callback.
- [..]
- Function @ref HAL_SMBUS_RegisterCallback() allows to register following callbacks:
- (+) MasterTxCpltCallback : callback for Master transmission end of transfer.
- (+) MasterRxCpltCallback : callback for Master reception end of transfer.
- (+) SlaveTxCpltCallback : callback for Slave transmission end of transfer.
- (+) SlaveRxCpltCallback : callback for Slave reception end of transfer.
- (+) ListenCpltCallback : callback for end of listen mode.
- (+) ErrorCallback : callback for error detection.
- (+) MspInitCallback : callback for Msp Init.
- (+) MspDeInitCallback : callback for Msp DeInit.
- This function takes as parameters the HAL peripheral handle, the Callback ID
- and a pointer to the user callback function.
- [..]
- For specific callback AddrCallback use dedicated register callbacks : @ref HAL_SMBUS_RegisterAddrCallback.
- [..]
- Use function @ref HAL_SMBUS_UnRegisterCallback to reset a callback to the default
- weak function.
- @ref HAL_SMBUS_UnRegisterCallback takes as parameters the HAL peripheral handle,
- and the Callback ID.
- This function allows to reset following callbacks:
- (+) MasterTxCpltCallback : callback for Master transmission end of transfer.
- (+) MasterRxCpltCallback : callback for Master reception end of transfer.
- (+) SlaveTxCpltCallback : callback for Slave transmission end of transfer.
- (+) SlaveRxCpltCallback : callback for Slave reception end of transfer.
- (+) ListenCpltCallback : callback for end of listen mode.
- (+) ErrorCallback : callback for error detection.
- (+) MspInitCallback : callback for Msp Init.
- (+) MspDeInitCallback : callback for Msp DeInit.
- [..]
- For callback AddrCallback use dedicated register callbacks : @ref HAL_SMBUS_UnRegisterAddrCallback.
- [..]
- By default, after the @ref HAL_SMBUS_Init() and when the state is @ref HAL_I2C_STATE_RESET
- all callbacks are set to the corresponding weak functions:
- examples @ref HAL_SMBUS_MasterTxCpltCallback(), @ref HAL_SMBUS_MasterRxCpltCallback().
- Exception done for MspInit and MspDeInit functions that are
- reset to the legacy weak functions in the @ref HAL_SMBUS_Init()/ @ref HAL_SMBUS_DeInit() only when
- these callbacks are null (not registered beforehand).
- If MspInit or MspDeInit are not null, the @ref HAL_SMBUS_Init()/ @ref HAL_SMBUS_DeInit()
- keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state.
- [..]
- Callbacks can be registered/unregistered in @ref HAL_I2C_STATE_READY state only.
- Exception done MspInit/MspDeInit functions that can be registered/unregistered
- in @ref HAL_I2C_STATE_READY or @ref HAL_I2C_STATE_RESET state,
- thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
- Then, the user first registers the MspInit/MspDeInit user callbacks
- using @ref HAL_SMBUS_RegisterCallback() before calling @ref HAL_SMBUS_DeInit()
- or @ref HAL_SMBUS_Init() function.
- [..]
- When the compilation flag USE_HAL_SMBUS_REGISTER_CALLBACKS is set to 0 or
- not defined, the callback registration feature is not available and all callbacks
- are set to the corresponding weak functions.
-
- [..]
- (@) You can refer to the SMBUS HAL driver header file for more useful macros
-
- @endverbatim
- ******************************************************************************
- * @attention
- *
- * <h2><center>© Copyright (c) 2016 STMicroelectronics.
- * All rights reserved.</center></h2>
- *
- * This software component is licensed by ST under BSD 3-Clause license,
- * the "License"; You may not use this file except in compliance with the
- * License. You may obtain a copy of the License at:
- * opensource.org/licenses/BSD-3-Clause
- *
- ******************************************************************************
- */
-
-/* Includes ------------------------------------------------------------------*/
-#include "stm32f0xx_hal.h"
-
-/** @addtogroup STM32F0xx_HAL_Driver
- * @{
- */
-
-/** @defgroup SMBUS SMBUS
- * @brief SMBUS HAL module driver
- * @{
- */
-
-#ifdef HAL_SMBUS_MODULE_ENABLED
-
-/* Private typedef -----------------------------------------------------------*/
-/* Private constants ---------------------------------------------------------*/
-/** @defgroup SMBUS_Private_Define SMBUS Private Constants
- * @{
- */
-#define TIMING_CLEAR_MASK (0xF0FFFFFFUL) /*!< SMBUS TIMING clear register Mask */
-#define HAL_TIMEOUT_ADDR (10000U) /*!< 10 s */
-#define HAL_TIMEOUT_BUSY (25U) /*!< 25 ms */
-#define HAL_TIMEOUT_DIR (25U) /*!< 25 ms */
-#define HAL_TIMEOUT_RXNE (25U) /*!< 25 ms */
-#define HAL_TIMEOUT_STOPF (25U) /*!< 25 ms */
-#define HAL_TIMEOUT_TC (25U) /*!< 25 ms */
-#define HAL_TIMEOUT_TCR (25U) /*!< 25 ms */
-#define HAL_TIMEOUT_TXIS (25U) /*!< 25 ms */
-#define MAX_NBYTE_SIZE 255U
-/**
- * @}
- */
-
-/* Private macro -------------------------------------------------------------*/
-/* Private variables ---------------------------------------------------------*/
-/* Private function prototypes -----------------------------------------------*/
-/** @addtogroup SMBUS_Private_Functions SMBUS Private Functions
- * @{
- */
-static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t Flag, FlagStatus Status, uint32_t Timeout);
-
-static void SMBUS_Enable_IRQ(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t InterruptRequest);
-static void SMBUS_Disable_IRQ(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t InterruptRequest);
-static HAL_StatusTypeDef SMBUS_Master_ISR(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t StatusFlags);
-static HAL_StatusTypeDef SMBUS_Slave_ISR(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t StatusFlags);
-
-static void SMBUS_ConvertOtherXferOptions(struct __SMBUS_HandleTypeDef *hsmbus);
-
-static void SMBUS_ITErrorHandler(struct __SMBUS_HandleTypeDef *hsmbus);
-
-static void SMBUS_TransferConfig(struct __SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request);
-/**
- * @}
- */
-
-/* Exported functions --------------------------------------------------------*/
-
-/** @defgroup SMBUS_Exported_Functions SMBUS Exported Functions
- * @{
- */
-
-/** @defgroup SMBUS_Exported_Functions_Group1 Initialization and de-initialization functions
- * @brief Initialization and Configuration functions
- *
-@verbatim
- ===============================================================================
- ##### Initialization and de-initialization functions #####
- ===============================================================================
- [..] This subsection provides a set of functions allowing to initialize and
- deinitialize the SMBUSx peripheral:
-
- (+) User must Implement HAL_SMBUS_MspInit() function in which he configures
- all related peripherals resources (CLOCK, GPIO, IT and NVIC ).
-
- (+) Call the function HAL_SMBUS_Init() to configure the selected device with
- the selected configuration:
- (++) Clock Timing
- (++) Bus Timeout
- (++) Analog Filer mode
- (++) Own Address 1
- (++) Addressing mode (Master, Slave)
- (++) Dual Addressing mode
- (++) Own Address 2
- (++) Own Address 2 Mask
- (++) General call mode
- (++) Nostretch mode
- (++) Packet Error Check mode
- (++) Peripheral mode
-
-
- (+) Call the function HAL_SMBUS_DeInit() to restore the default configuration
- of the selected SMBUSx peripheral.
-
- (+) Enable/Disable Analog/Digital filters with HAL_SMBUS_ConfigAnalogFilter() and
- HAL_SMBUS_ConfigDigitalFilter().
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Initialize the SMBUS according to the specified parameters
- * in the SMBUS_InitTypeDef and initialize the associated handle.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Init(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Check the SMBUS handle allocation */
- if (hsmbus == NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance));
- assert_param(IS_SMBUS_ANALOG_FILTER(hsmbus->Init.AnalogFilter));
- assert_param(IS_SMBUS_OWN_ADDRESS1(hsmbus->Init.OwnAddress1));
- assert_param(IS_SMBUS_ADDRESSING_MODE(hsmbus->Init.AddressingMode));
- assert_param(IS_SMBUS_DUAL_ADDRESS(hsmbus->Init.DualAddressMode));
- assert_param(IS_SMBUS_OWN_ADDRESS2(hsmbus->Init.OwnAddress2));
- assert_param(IS_SMBUS_OWN_ADDRESS2_MASK(hsmbus->Init.OwnAddress2Masks));
- assert_param(IS_SMBUS_GENERAL_CALL(hsmbus->Init.GeneralCallMode));
- assert_param(IS_SMBUS_NO_STRETCH(hsmbus->Init.NoStretchMode));
- assert_param(IS_SMBUS_PEC(hsmbus->Init.PacketErrorCheckMode));
- assert_param(IS_SMBUS_PERIPHERAL_MODE(hsmbus->Init.PeripheralMode));
-
- if (hsmbus->State == HAL_SMBUS_STATE_RESET)
- {
- /* Allocate lock resource and initialize it */
- hsmbus->Lock = HAL_UNLOCKED;
-
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->MasterTxCpltCallback = HAL_SMBUS_MasterTxCpltCallback; /* Legacy weak MasterTxCpltCallback */
- hsmbus->MasterRxCpltCallback = HAL_SMBUS_MasterRxCpltCallback; /* Legacy weak MasterRxCpltCallback */
- hsmbus->SlaveTxCpltCallback = HAL_SMBUS_SlaveTxCpltCallback; /* Legacy weak SlaveTxCpltCallback */
- hsmbus->SlaveRxCpltCallback = HAL_SMBUS_SlaveRxCpltCallback; /* Legacy weak SlaveRxCpltCallback */
- hsmbus->ListenCpltCallback = HAL_SMBUS_ListenCpltCallback; /* Legacy weak ListenCpltCallback */
- hsmbus->ErrorCallback = HAL_SMBUS_ErrorCallback; /* Legacy weak ErrorCallback */
- hsmbus->AddrCallback = HAL_SMBUS_AddrCallback; /* Legacy weak AddrCallback */
-
- if (hsmbus->MspInitCallback == NULL)
- {
- hsmbus->MspInitCallback = HAL_SMBUS_MspInit; /* Legacy weak MspInit */
- }
-
- /* Init the low level hardware : GPIO, CLOCK, CORTEX...etc */
- hsmbus->MspInitCallback(hsmbus);
-#else
- /* Init the low level hardware : GPIO, CLOCK, NVIC */
- HAL_SMBUS_MspInit(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
-
- hsmbus->State = HAL_SMBUS_STATE_BUSY;
-
- /* Disable the selected SMBUS peripheral */
- __HAL_SMBUS_DISABLE(hsmbus);
-
- /*---------------------------- SMBUSx TIMINGR Configuration ------------------------*/
- /* Configure SMBUSx: Frequency range */
- hsmbus->Instance->TIMINGR = hsmbus->Init.Timing & TIMING_CLEAR_MASK;
-
- /*---------------------------- SMBUSx TIMEOUTR Configuration ------------------------*/
- /* Configure SMBUSx: Bus Timeout */
- hsmbus->Instance->TIMEOUTR &= ~I2C_TIMEOUTR_TIMOUTEN;
- hsmbus->Instance->TIMEOUTR &= ~I2C_TIMEOUTR_TEXTEN;
- hsmbus->Instance->TIMEOUTR = hsmbus->Init.SMBusTimeout;
-
- /*---------------------------- SMBUSx OAR1 Configuration -----------------------*/
- /* Configure SMBUSx: Own Address1 and ack own address1 mode */
- hsmbus->Instance->OAR1 &= ~I2C_OAR1_OA1EN;
-
- if (hsmbus->Init.OwnAddress1 != 0UL)
- {
- if (hsmbus->Init.AddressingMode == SMBUS_ADDRESSINGMODE_7BIT)
- {
- hsmbus->Instance->OAR1 = (I2C_OAR1_OA1EN | hsmbus->Init.OwnAddress1);
- }
- else /* SMBUS_ADDRESSINGMODE_10BIT */
- {
- hsmbus->Instance->OAR1 = (I2C_OAR1_OA1EN | I2C_OAR1_OA1MODE | hsmbus->Init.OwnAddress1);
- }
- }
-
- /*---------------------------- SMBUSx CR2 Configuration ------------------------*/
- /* Configure SMBUSx: Addressing Master mode */
- if (hsmbus->Init.AddressingMode == SMBUS_ADDRESSINGMODE_10BIT)
- {
- hsmbus->Instance->CR2 = (I2C_CR2_ADD10);
- }
- /* Enable the AUTOEND by default, and enable NACK (should be disable only during Slave process) */
- /* AUTOEND and NACK bit will be manage during Transfer process */
- hsmbus->Instance->CR2 |= (I2C_CR2_AUTOEND | I2C_CR2_NACK);
-
- /*---------------------------- SMBUSx OAR2 Configuration -----------------------*/
- /* Configure SMBUSx: Dual mode and Own Address2 */
- hsmbus->Instance->OAR2 = (hsmbus->Init.DualAddressMode | hsmbus->Init.OwnAddress2 | (hsmbus->Init.OwnAddress2Masks << 8U));
-
- /*---------------------------- SMBUSx CR1 Configuration ------------------------*/
- /* Configure SMBUSx: Generalcall and NoStretch mode */
- hsmbus->Instance->CR1 = (hsmbus->Init.GeneralCallMode | hsmbus->Init.NoStretchMode | hsmbus->Init.PacketErrorCheckMode | hsmbus->Init.PeripheralMode | hsmbus->Init.AnalogFilter);
-
- /* Enable Slave Byte Control only in case of Packet Error Check is enabled and SMBUS Peripheral is set in Slave mode */
- if ((hsmbus->Init.PacketErrorCheckMode == SMBUS_PEC_ENABLE)
- && ((hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE) || (hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE_ARP)))
- {
- hsmbus->Instance->CR1 |= I2C_CR1_SBC;
- }
-
- /* Enable the selected SMBUS peripheral */
- __HAL_SMBUS_ENABLE(hsmbus);
-
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
- hsmbus->PreviousState = HAL_SMBUS_STATE_READY;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @brief DeInitialize the SMBUS peripheral.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_DeInit(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Check the SMBUS handle allocation */
- if (hsmbus == NULL)
- {
- return HAL_ERROR;
- }
-
- /* Check the parameters */
- assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance));
-
- hsmbus->State = HAL_SMBUS_STATE_BUSY;
-
- /* Disable the SMBUS Peripheral Clock */
- __HAL_SMBUS_DISABLE(hsmbus);
-
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- if (hsmbus->MspDeInitCallback == NULL)
- {
- hsmbus->MspDeInitCallback = HAL_SMBUS_MspDeInit; /* Legacy weak MspDeInit */
- }
-
- /* DeInit the low level hardware: GPIO, CLOCK, NVIC */
- hsmbus->MspDeInitCallback(hsmbus);
-#else
- /* DeInit the low level hardware: GPIO, CLOCK, NVIC */
- HAL_SMBUS_MspDeInit(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
-
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
- hsmbus->PreviousState = HAL_SMBUS_STATE_RESET;
- hsmbus->State = HAL_SMBUS_STATE_RESET;
-
- /* Release Lock */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
-}
-
-/**
- * @brief Initialize the SMBUS MSP.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_MspInit(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hsmbus);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_SMBUS_MspInit could be implemented in the user file
- */
-}
-
-/**
- * @brief DeInitialize the SMBUS MSP.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_MspDeInit(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hsmbus);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_SMBUS_MspDeInit could be implemented in the user file
- */
-}
-
-/**
- * @brief Configure Analog noise filter.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param AnalogFilter This parameter can be one of the following values:
- * @arg @ref SMBUS_ANALOGFILTER_ENABLE
- * @arg @ref SMBUS_ANALOGFILTER_DISABLE
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_ConfigAnalogFilter(SMBUS_HandleTypeDef *hsmbus, uint32_t AnalogFilter)
-{
- /* Check the parameters */
- assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance));
- assert_param(IS_SMBUS_ANALOG_FILTER(AnalogFilter));
-
- if (hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_BUSY;
-
- /* Disable the selected SMBUS peripheral */
- __HAL_SMBUS_DISABLE(hsmbus);
-
- /* Reset ANOFF bit */
- hsmbus->Instance->CR1 &= ~(I2C_CR1_ANFOFF);
-
- /* Set analog filter bit*/
- hsmbus->Instance->CR1 |= AnalogFilter;
-
- __HAL_SMBUS_ENABLE(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Configure Digital noise filter.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param DigitalFilter Coefficient of digital noise filter between Min_Data=0x00 and Max_Data=0x0F.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_ConfigDigitalFilter(SMBUS_HandleTypeDef *hsmbus, uint32_t DigitalFilter)
-{
- uint32_t tmpreg;
-
- /* Check the parameters */
- assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance));
- assert_param(IS_SMBUS_DIGITAL_FILTER(DigitalFilter));
-
- if (hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_BUSY;
-
- /* Disable the selected SMBUS peripheral */
- __HAL_SMBUS_DISABLE(hsmbus);
-
- /* Get the old register value */
- tmpreg = hsmbus->Instance->CR1;
-
- /* Reset I2C DNF bits [11:8] */
- tmpreg &= ~(I2C_CR1_DNF);
-
- /* Set I2Cx DNF coefficient */
- tmpreg |= DigitalFilter << I2C_CR1_DNF_Pos;
-
- /* Store the new register value */
- hsmbus->Instance->CR1 = tmpreg;
-
- __HAL_SMBUS_ENABLE(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
-/**
- * @brief Register a User SMBUS Callback
- * To be used instead of the weak predefined callback
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param CallbackID ID of the callback to be registered
- * This parameter can be one of the following values:
- * @arg @ref HAL_SMBUS_MASTER_TX_COMPLETE_CB_ID Master Tx Transfer completed callback ID
- * @arg @ref HAL_SMBUS_MASTER_RX_COMPLETE_CB_ID Master Rx Transfer completed callback ID
- * @arg @ref HAL_SMBUS_SLAVE_TX_COMPLETE_CB_ID Slave Tx Transfer completed callback ID
- * @arg @ref HAL_SMBUS_SLAVE_RX_COMPLETE_CB_ID Slave Rx Transfer completed callback ID
- * @arg @ref HAL_SMBUS_LISTEN_COMPLETE_CB_ID Listen Complete callback ID
- * @arg @ref HAL_SMBUS_ERROR_CB_ID Error callback ID
- * @arg @ref HAL_SMBUS_MSPINIT_CB_ID MspInit callback ID
- * @arg @ref HAL_SMBUS_MSPDEINIT_CB_ID MspDeInit callback ID
- * @param pCallback pointer to the Callback function
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_RegisterCallback(SMBUS_HandleTypeDef *hsmbus, HAL_SMBUS_CallbackIDTypeDef CallbackID, pSMBUS_CallbackTypeDef pCallback)
-{
- HAL_StatusTypeDef status = HAL_OK;
-
- if (pCallback == NULL)
- {
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- return HAL_ERROR;
- }
-
- /* Process locked */
- __HAL_LOCK(hsmbus);
-
- if (HAL_SMBUS_STATE_READY == hsmbus->State)
- {
- switch (CallbackID)
- {
- case HAL_SMBUS_MASTER_TX_COMPLETE_CB_ID :
- hsmbus->MasterTxCpltCallback = pCallback;
- break;
-
- case HAL_SMBUS_MASTER_RX_COMPLETE_CB_ID :
- hsmbus->MasterRxCpltCallback = pCallback;
- break;
-
- case HAL_SMBUS_SLAVE_TX_COMPLETE_CB_ID :
- hsmbus->SlaveTxCpltCallback = pCallback;
- break;
-
- case HAL_SMBUS_SLAVE_RX_COMPLETE_CB_ID :
- hsmbus->SlaveRxCpltCallback = pCallback;
- break;
-
- case HAL_SMBUS_LISTEN_COMPLETE_CB_ID :
- hsmbus->ListenCpltCallback = pCallback;
- break;
-
- case HAL_SMBUS_ERROR_CB_ID :
- hsmbus->ErrorCallback = pCallback;
- break;
-
- case HAL_SMBUS_MSPINIT_CB_ID :
- hsmbus->MspInitCallback = pCallback;
- break;
-
- case HAL_SMBUS_MSPDEINIT_CB_ID :
- hsmbus->MspDeInitCallback = pCallback;
- break;
-
- default :
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- /* Return error status */
- status = HAL_ERROR;
- break;
- }
- }
- else if (HAL_SMBUS_STATE_RESET == hsmbus->State)
- {
- switch (CallbackID)
- {
- case HAL_SMBUS_MSPINIT_CB_ID :
- hsmbus->MspInitCallback = pCallback;
- break;
-
- case HAL_SMBUS_MSPDEINIT_CB_ID :
- hsmbus->MspDeInitCallback = pCallback;
- break;
-
- default :
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- /* Return error status */
- status = HAL_ERROR;
- break;
- }
- }
- else
- {
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- /* Return error status */
- status = HAL_ERROR;
- }
-
- /* Release Lock */
- __HAL_UNLOCK(hsmbus);
- return status;
-}
-
-/**
- * @brief Unregister an SMBUS Callback
- * SMBUS callback is redirected to the weak predefined callback
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param CallbackID ID of the callback to be unregistered
- * This parameter can be one of the following values:
- * This parameter can be one of the following values:
- * @arg @ref HAL_SMBUS_MASTER_TX_COMPLETE_CB_ID Master Tx Transfer completed callback ID
- * @arg @ref HAL_SMBUS_MASTER_RX_COMPLETE_CB_ID Master Rx Transfer completed callback ID
- * @arg @ref HAL_SMBUS_SLAVE_TX_COMPLETE_CB_ID Slave Tx Transfer completed callback ID
- * @arg @ref HAL_SMBUS_SLAVE_RX_COMPLETE_CB_ID Slave Rx Transfer completed callback ID
- * @arg @ref HAL_SMBUS_LISTEN_COMPLETE_CB_ID Listen Complete callback ID
- * @arg @ref HAL_SMBUS_ERROR_CB_ID Error callback ID
- * @arg @ref HAL_SMBUS_MSPINIT_CB_ID MspInit callback ID
- * @arg @ref HAL_SMBUS_MSPDEINIT_CB_ID MspDeInit callback ID
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_UnRegisterCallback(SMBUS_HandleTypeDef *hsmbus, HAL_SMBUS_CallbackIDTypeDef CallbackID)
-{
- HAL_StatusTypeDef status = HAL_OK;
-
- /* Process locked */
- __HAL_LOCK(hsmbus);
-
- if (HAL_SMBUS_STATE_READY == hsmbus->State)
- {
- switch (CallbackID)
- {
- case HAL_SMBUS_MASTER_TX_COMPLETE_CB_ID :
- hsmbus->MasterTxCpltCallback = HAL_SMBUS_MasterTxCpltCallback; /* Legacy weak MasterTxCpltCallback */
- break;
-
- case HAL_SMBUS_MASTER_RX_COMPLETE_CB_ID :
- hsmbus->MasterRxCpltCallback = HAL_SMBUS_MasterRxCpltCallback; /* Legacy weak MasterRxCpltCallback */
- break;
-
- case HAL_SMBUS_SLAVE_TX_COMPLETE_CB_ID :
- hsmbus->SlaveTxCpltCallback = HAL_SMBUS_SlaveTxCpltCallback; /* Legacy weak SlaveTxCpltCallback */
- break;
-
- case HAL_SMBUS_SLAVE_RX_COMPLETE_CB_ID :
- hsmbus->SlaveRxCpltCallback = HAL_SMBUS_SlaveRxCpltCallback; /* Legacy weak SlaveRxCpltCallback */
- break;
-
- case HAL_SMBUS_LISTEN_COMPLETE_CB_ID :
- hsmbus->ListenCpltCallback = HAL_SMBUS_ListenCpltCallback; /* Legacy weak ListenCpltCallback */
- break;
-
- case HAL_SMBUS_ERROR_CB_ID :
- hsmbus->ErrorCallback = HAL_SMBUS_ErrorCallback; /* Legacy weak ErrorCallback */
- break;
-
- case HAL_SMBUS_MSPINIT_CB_ID :
- hsmbus->MspInitCallback = HAL_SMBUS_MspInit; /* Legacy weak MspInit */
- break;
-
- case HAL_SMBUS_MSPDEINIT_CB_ID :
- hsmbus->MspDeInitCallback = HAL_SMBUS_MspDeInit; /* Legacy weak MspDeInit */
- break;
-
- default :
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- /* Return error status */
- status = HAL_ERROR;
- break;
- }
- }
- else if (HAL_SMBUS_STATE_RESET == hsmbus->State)
- {
- switch (CallbackID)
- {
- case HAL_SMBUS_MSPINIT_CB_ID :
- hsmbus->MspInitCallback = HAL_SMBUS_MspInit; /* Legacy weak MspInit */
- break;
-
- case HAL_SMBUS_MSPDEINIT_CB_ID :
- hsmbus->MspDeInitCallback = HAL_SMBUS_MspDeInit; /* Legacy weak MspDeInit */
- break;
-
- default :
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- /* Return error status */
- status = HAL_ERROR;
- break;
- }
- }
- else
- {
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- /* Return error status */
- status = HAL_ERROR;
- }
-
- /* Release Lock */
- __HAL_UNLOCK(hsmbus);
- return status;
-}
-
-/**
- * @brief Register the Slave Address Match SMBUS Callback
- * To be used instead of the weak HAL_SMBUS_AddrCallback() predefined callback
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param pCallback pointer to the Address Match Callback function
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_RegisterAddrCallback(SMBUS_HandleTypeDef *hsmbus, pSMBUS_AddrCallbackTypeDef pCallback)
-{
- HAL_StatusTypeDef status = HAL_OK;
-
- if (pCallback == NULL)
- {
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- return HAL_ERROR;
- }
- /* Process locked */
- __HAL_LOCK(hsmbus);
-
- if (HAL_SMBUS_STATE_READY == hsmbus->State)
- {
- hsmbus->AddrCallback = pCallback;
- }
- else
- {
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- /* Return error status */
- status = HAL_ERROR;
- }
-
- /* Release Lock */
- __HAL_UNLOCK(hsmbus);
- return status;
-}
-
-/**
- * @brief UnRegister the Slave Address Match SMBUS Callback
- * Info Ready SMBUS Callback is redirected to the weak HAL_SMBUS_AddrCallback() predefined callback
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_UnRegisterAddrCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- HAL_StatusTypeDef status = HAL_OK;
-
- /* Process locked */
- __HAL_LOCK(hsmbus);
-
- if (HAL_SMBUS_STATE_READY == hsmbus->State)
- {
- hsmbus->AddrCallback = HAL_SMBUS_AddrCallback; /* Legacy weak AddrCallback */
- }
- else
- {
- /* Update the error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_INVALID_CALLBACK;
-
- /* Return error status */
- status = HAL_ERROR;
- }
-
- /* Release Lock */
- __HAL_UNLOCK(hsmbus);
- return status;
-}
-
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
-
-/**
- * @}
- */
-
-/** @defgroup SMBUS_Exported_Functions_Group2 Input and Output operation functions
- * @brief Data transfers functions
- *
-@verbatim
- ===============================================================================
- ##### IO operation functions #####
- ===============================================================================
- [..]
- This subsection provides a set of functions allowing to manage the SMBUS data
- transfers.
-
- (#) Blocking mode function to check if device is ready for usage is :
- (++) HAL_SMBUS_IsDeviceReady()
-
- (#) There is only one mode of transfer:
- (++) Non-Blocking mode : The communication is performed using Interrupts.
- These functions return the status of the transfer startup.
- The end of the data processing will be indicated through the
- dedicated SMBUS IRQ when using Interrupt mode.
-
- (#) Non-Blocking mode functions with Interrupt are :
- (++) HAL_SMBUS_Master_Transmit_IT()
- (++) HAL_SMBUS_Master_Receive_IT()
- (++) HAL_SMBUS_Slave_Transmit_IT()
- (++) HAL_SMBUS_Slave_Receive_IT()
- (++) HAL_SMBUS_EnableListen_IT() or alias HAL_SMBUS_EnableListen_IT()
- (++) HAL_SMBUS_DisableListen_IT()
- (++) HAL_SMBUS_EnableAlert_IT()
- (++) HAL_SMBUS_DisableAlert_IT()
-
- (#) A set of Transfer Complete Callbacks are provided in non-Blocking mode:
- (++) HAL_SMBUS_MasterTxCpltCallback()
- (++) HAL_SMBUS_MasterRxCpltCallback()
- (++) HAL_SMBUS_SlaveTxCpltCallback()
- (++) HAL_SMBUS_SlaveRxCpltCallback()
- (++) HAL_SMBUS_AddrCallback()
- (++) HAL_SMBUS_ListenCpltCallback()
- (++) HAL_SMBUS_ErrorCallback()
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Transmit in master/host SMBUS mode an amount of data in non-blocking mode with Interrupt.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param DevAddress Target device address: The device 7 bits address value
- * in datasheet must be shifted to the left before calling the interface
- * @param pData Pointer to data buffer
- * @param Size Amount of data to be sent
- * @param XferOptions Options of Transfer, value of @ref SMBUS_XferOptions_definition
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Master_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions)
-{
- uint32_t tmp;
-
- /* Check the parameters */
- assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions));
-
- if (hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_TX;
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
- /* Prepare transfer parameters */
- hsmbus->pBuffPtr = pData;
- hsmbus->XferCount = Size;
- hsmbus->XferOptions = XferOptions;
-
- /* In case of Quick command, remove autoend mode */
- /* Manage the stop generation by software */
- if (hsmbus->pBuffPtr == NULL)
- {
- hsmbus->XferOptions &= ~SMBUS_AUTOEND_MODE;
- }
-
- if (Size > MAX_NBYTE_SIZE)
- {
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = Size;
- }
-
- /* Send Slave Address */
- /* Set NBYTES to write and reload if size > MAX_NBYTE_SIZE and generate RESTART */
- if ((hsmbus->XferSize < hsmbus->XferCount) && (hsmbus->XferSize == MAX_NBYTE_SIZE))
- {
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_GENERATE_START_WRITE);
- }
- else
- {
- /* If transfer direction not change, do not generate Restart Condition */
- /* Mean Previous state is same as current state */
-
- /* Store current volatile XferOptions, misra rule */
- tmp = hsmbus->XferOptions;
-
- if ((hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_TX) && (IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(tmp) == 0))
- {
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- }
- /* Else transfer direction change, so generate Restart with new transfer direction */
- else
- {
- /* Convert OTHER_xxx XferOptions if any */
- SMBUS_ConvertOtherXferOptions(hsmbus);
-
- /* Handle Transfer */
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_GENERATE_START_WRITE);
- }
-
- /* If PEC mode is enable, size to transmit manage by SW part should be Size-1 byte, corresponding to PEC byte */
- /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
- if (SMBUS_GET_PEC_MODE(hsmbus) != 0UL)
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_TX);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Receive in master/host SMBUS mode an amount of data in non-blocking mode with Interrupt.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param DevAddress Target device address: The device 7 bits address value
- * in datasheet must be shifted to the left before calling the interface
- * @param pData Pointer to data buffer
- * @param Size Amount of data to be sent
- * @param XferOptions Options of Transfer, value of @ref SMBUS_XferOptions_definition
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Master_Receive_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions)
-{
- uint32_t tmp;
-
- /* Check the parameters */
- assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions));
-
- if (hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_RX;
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- /* Prepare transfer parameters */
- hsmbus->pBuffPtr = pData;
- hsmbus->XferCount = Size;
- hsmbus->XferOptions = XferOptions;
-
- /* In case of Quick command, remove autoend mode */
- /* Manage the stop generation by software */
- if (hsmbus->pBuffPtr == NULL)
- {
- hsmbus->XferOptions &= ~SMBUS_AUTOEND_MODE;
- }
-
- if (Size > MAX_NBYTE_SIZE)
- {
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = Size;
- }
-
- /* Send Slave Address */
- /* Set NBYTES to write and reload if size > MAX_NBYTE_SIZE and generate RESTART */
- if ((hsmbus->XferSize < hsmbus->XferCount) && (hsmbus->XferSize == MAX_NBYTE_SIZE))
- {
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_GENERATE_START_READ);
- }
- else
- {
- /* If transfer direction not change, do not generate Restart Condition */
- /* Mean Previous state is same as current state */
-
- /* Store current volatile XferOptions, Misra rule */
- tmp = hsmbus->XferOptions;
-
- if ((hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_RX) && (IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(tmp) == 0))
- {
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- }
- /* Else transfer direction change, so generate Restart with new transfer direction */
- else
- {
- /* Convert OTHER_xxx XferOptions if any */
- SMBUS_ConvertOtherXferOptions(hsmbus);
-
- /* Handle Transfer */
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_GENERATE_START_READ);
- }
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_RX);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Abort a master/host SMBUS process communication with Interrupt.
- * @note This abort can be called only if state is ready
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param DevAddress Target device address: The device 7 bits address value
- * in datasheet must be shifted to the left before calling the interface
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Master_Abort_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress)
-{
- if (hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- /* Keep the same state as previous */
- /* to perform as well the call of the corresponding end of transfer callback */
- if (hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_TX;
- }
- else if (hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_RX;
- }
- else
- {
- /* Wrong usage of abort function */
- /* This function should be used only in case of abort monitored by master device */
- return HAL_ERROR;
- }
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- /* Set NBYTES to 1 to generate a dummy read on SMBUS peripheral */
- /* Set AUTOEND mode, this will generate a NACK then STOP condition to abort the current transfer */
- SMBUS_TransferConfig(hsmbus, DevAddress, 1, SMBUS_AUTOEND_MODE, SMBUS_NO_STARTSTOP);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- if (hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_TX);
- }
- else if (hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_RX);
- }
- else
- {
- /* Nothing to do */
- }
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Transmit in slave/device SMBUS mode an amount of data in non-blocking mode with Interrupt.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param pData Pointer to data buffer
- * @param Size Amount of data to be sent
- * @param XferOptions Options of Transfer, value of @ref SMBUS_XferOptions_definition
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Slave_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint8_t *pData, uint16_t Size, uint32_t XferOptions)
-{
- /* Check the parameters */
- assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions));
-
- if ((hsmbus->State & HAL_SMBUS_STATE_LISTEN) == HAL_SMBUS_STATE_LISTEN)
- {
- if ((pData == NULL) || (Size == 0UL))
- {
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_INVALID_PARAM;
- return HAL_ERROR;
- }
-
- /* Disable Interrupts, to prevent preemption during treatment in case of multicall */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR | SMBUS_IT_TX);
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = (HAL_SMBUS_STATE_SLAVE_BUSY_TX | HAL_SMBUS_STATE_LISTEN);
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- /* Set SBC bit to manage Acknowledge at each bit */
- hsmbus->Instance->CR1 |= I2C_CR1_SBC;
-
- /* Enable Address Acknowledge */
- hsmbus->Instance->CR2 &= ~I2C_CR2_NACK;
-
- /* Prepare transfer parameters */
- hsmbus->pBuffPtr = pData;
- hsmbus->XferCount = Size;
- hsmbus->XferOptions = XferOptions;
-
- /* Convert OTHER_xxx XferOptions if any */
- SMBUS_ConvertOtherXferOptions(hsmbus);
-
- if (Size > MAX_NBYTE_SIZE)
- {
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = Size;
- }
-
- /* Set NBYTES to write and reload if size > MAX_NBYTE_SIZE and generate RESTART */
- if ((hsmbus->XferSize < hsmbus->XferCount) && (hsmbus->XferSize == MAX_NBYTE_SIZE))
- {
- SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_NO_STARTSTOP);
- }
- else
- {
- /* Set NBYTE to transmit */
- SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
-
- /* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */
- /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
- if (SMBUS_GET_PEC_MODE(hsmbus) != 0UL)
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
-
- /* Clear ADDR flag after prepare the transfer parameters */
- /* This action will generate an acknowledge to the HOST */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ADDR);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- /* REnable ADDR interrupt */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_TX | SMBUS_IT_ADDR);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Receive in slave/device SMBUS mode an amount of data in non-blocking mode with Interrupt.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param pData Pointer to data buffer
- * @param Size Amount of data to be sent
- * @param XferOptions Options of Transfer, value of @ref SMBUS_XferOptions_definition
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_Slave_Receive_IT(SMBUS_HandleTypeDef *hsmbus, uint8_t *pData, uint16_t Size, uint32_t XferOptions)
-{
- /* Check the parameters */
- assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions));
-
- if ((hsmbus->State & HAL_SMBUS_STATE_LISTEN) == HAL_SMBUS_STATE_LISTEN)
- {
- if ((pData == NULL) || (Size == 0UL))
- {
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_INVALID_PARAM;
- return HAL_ERROR;
- }
-
- /* Disable Interrupts, to prevent preemption during treatment in case of multicall */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR | SMBUS_IT_RX);
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = (HAL_SMBUS_STATE_SLAVE_BUSY_RX | HAL_SMBUS_STATE_LISTEN);
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- /* Set SBC bit to manage Acknowledge at each bit */
- hsmbus->Instance->CR1 |= I2C_CR1_SBC;
-
- /* Enable Address Acknowledge */
- hsmbus->Instance->CR2 &= ~I2C_CR2_NACK;
-
- /* Prepare transfer parameters */
- hsmbus->pBuffPtr = pData;
- hsmbus->XferSize = Size;
- hsmbus->XferCount = Size;
- hsmbus->XferOptions = XferOptions;
-
- /* Convert OTHER_xxx XferOptions if any */
- SMBUS_ConvertOtherXferOptions(hsmbus);
-
- /* Set NBYTE to receive */
- /* If XferSize equal "1", or XferSize equal "2" with PEC requested (mean 1 data byte + 1 PEC byte */
- /* no need to set RELOAD bit mode, a ACK will be automatically generated in that case */
- /* else need to set RELOAD bit mode to generate an automatic ACK at each byte Received */
- /* This RELOAD bit will be reset for last BYTE to be receive in SMBUS_Slave_ISR */
- if (((SMBUS_GET_PEC_MODE(hsmbus) != 0UL) && (hsmbus->XferSize == 2U)) || (hsmbus->XferSize == 1U))
- {
- SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- }
- else
- {
- SMBUS_TransferConfig(hsmbus, 0, 1, hsmbus->XferOptions | SMBUS_RELOAD_MODE, SMBUS_NO_STARTSTOP);
- }
-
- /* Clear ADDR flag after prepare the transfer parameters */
- /* This action will generate an acknowledge to the HOST */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ADDR);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Note : The SMBUS interrupts must be enabled after unlocking current process
- to avoid the risk of SMBUS interrupt handle execution before current
- process unlock */
- /* REnable ADDR interrupt */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_RX | SMBUS_IT_ADDR);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Enable the Address listen mode with Interrupt.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_EnableListen_IT(SMBUS_HandleTypeDef *hsmbus)
-{
- hsmbus->State = HAL_SMBUS_STATE_LISTEN;
-
- /* Enable the Address Match interrupt */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_ADDR);
-
- return HAL_OK;
-}
-
-/**
- * @brief Disable the Address listen mode with Interrupt.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_DisableListen_IT(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Disable Address listen mode only if a transfer is not ongoing */
- if (hsmbus->State == HAL_SMBUS_STATE_LISTEN)
- {
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Disable the Address Match interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR);
-
- return HAL_OK;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-
-/**
- * @brief Enable the SMBUS alert mode with Interrupt.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUSx peripheral.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_EnableAlert_IT(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Enable SMBus alert */
- hsmbus->Instance->CR1 |= I2C_CR1_ALERTEN;
-
- /* Clear ALERT flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ALERT);
-
- /* Enable Alert Interrupt */
- SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_ALERT);
-
- return HAL_OK;
-}
-/**
- * @brief Disable the SMBUS alert mode with Interrupt.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUSx peripheral.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_DisableAlert_IT(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Enable SMBus alert */
- hsmbus->Instance->CR1 &= ~I2C_CR1_ALERTEN;
-
- /* Disable Alert Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ALERT);
-
- return HAL_OK;
-}
-
-/**
- * @brief Check if target device is ready for communication.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param DevAddress Target device address: The device 7 bits address value
- * in datasheet must be shifted to the left before calling the interface
- * @param Trials Number of trials
- * @param Timeout Timeout duration
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_SMBUS_IsDeviceReady(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint32_t Trials, uint32_t Timeout)
-{
- uint32_t tickstart;
-
- __IO uint32_t SMBUS_Trials = 0UL;
-
- FlagStatus tmp1;
- FlagStatus tmp2;
-
- if (hsmbus->State == HAL_SMBUS_STATE_READY)
- {
- if (__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_BUSY) != RESET)
- {
- return HAL_BUSY;
- }
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- hsmbus->State = HAL_SMBUS_STATE_BUSY;
- hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE;
-
- do
- {
- /* Generate Start */
- hsmbus->Instance->CR2 = SMBUS_GENERATE_START(hsmbus->Init.AddressingMode, DevAddress);
-
- /* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */
- /* Wait until STOPF flag is set or a NACK flag is set*/
- tickstart = HAL_GetTick();
-
- tmp1 = __HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_STOPF);
- tmp2 = __HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF);
-
- while ((tmp1 == RESET) && (tmp2 == RESET))
- {
- if (Timeout != HAL_MAX_DELAY)
- {
- if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0UL))
- {
- /* Device is ready */
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Update SMBUS error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_HALTIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
- return HAL_ERROR;
- }
- }
-
- tmp1 = __HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_STOPF);
- tmp2 = __HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF);
- }
-
- /* Check if the NACKF flag has not been set */
- if (__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF) == RESET)
- {
- /* Wait until STOPF flag is reset */
- if (SMBUS_WaitOnFlagUntilTimeout(hsmbus, SMBUS_FLAG_STOPF, RESET, Timeout) != HAL_OK)
- {
- return HAL_ERROR;
- }
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
-
- /* Device is ready */
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
- }
- else
- {
- /* Wait until STOPF flag is reset */
- if (SMBUS_WaitOnFlagUntilTimeout(hsmbus, SMBUS_FLAG_STOPF, RESET, Timeout) != HAL_OK)
- {
- return HAL_ERROR;
- }
-
- /* Clear NACK Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF);
-
- /* Clear STOP Flag, auto generated with autoend*/
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
- }
-
- /* Check if the maximum allowed number of trials has been reached */
- if (SMBUS_Trials == Trials)
- {
- /* Generate Stop */
- hsmbus->Instance->CR2 |= I2C_CR2_STOP;
-
- /* Wait until STOPF flag is reset */
- if (SMBUS_WaitOnFlagUntilTimeout(hsmbus, SMBUS_FLAG_STOPF, RESET, Timeout) != HAL_OK)
- {
- return HAL_ERROR;
- }
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
- }
-
- /* Increment Trials */
- SMBUS_Trials++;
- }
- while (SMBUS_Trials < Trials);
-
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Update SMBUS error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_HALTIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_ERROR;
- }
- else
- {
- return HAL_BUSY;
- }
-}
-/**
- * @}
- */
-
-/** @defgroup SMBUS_IRQ_Handler_and_Callbacks IRQ Handler and Callbacks
- * @{
- */
-
-/**
- * @brief Handle SMBUS event interrupt request.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-void HAL_SMBUS_EV_IRQHandler(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Use a local variable to store the current ISR flags */
- /* This action will avoid a wrong treatment due to ISR flags change during interrupt handler */
- uint32_t tmpisrvalue = READ_REG(hsmbus->Instance->ISR);
- uint32_t tmpcr1value = READ_REG(hsmbus->Instance->CR1);
-
- /* SMBUS in mode Transmitter ---------------------------------------------------*/
- if ((SMBUS_CHECK_IT_SOURCE(tmpcr1value, (SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_TXI)) != RESET) && ((SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TXIS) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TCR) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TC) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_STOPF) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_AF) != RESET)))
- {
- /* Slave mode selected */
- if ((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_TX) == HAL_SMBUS_STATE_SLAVE_BUSY_TX)
- {
- (void)SMBUS_Slave_ISR(hsmbus, tmpisrvalue);
- }
- /* Master mode selected */
- else if ((hsmbus->State & HAL_SMBUS_STATE_MASTER_BUSY_TX) == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- (void)SMBUS_Master_ISR(hsmbus, tmpisrvalue);
- }
- else
- {
- /* Nothing to do */
- }
- }
-
- /* SMBUS in mode Receiver ----------------------------------------------------*/
- if ((SMBUS_CHECK_IT_SOURCE(tmpcr1value, (SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_RXI)) != RESET) && ((SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_RXNE) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TCR) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TC) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_STOPF) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_AF) != RESET)))
- {
- /* Slave mode selected */
- if ((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_RX) == HAL_SMBUS_STATE_SLAVE_BUSY_RX)
- {
- (void)SMBUS_Slave_ISR(hsmbus, tmpisrvalue);
- }
- /* Master mode selected */
- else if ((hsmbus->State & HAL_SMBUS_STATE_MASTER_BUSY_RX) == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- (void)SMBUS_Master_ISR(hsmbus, tmpisrvalue);
- }
- else
- {
- /* Nothing to do */
- }
- }
-
- /* SMBUS in mode Listener Only --------------------------------------------------*/
- if (((SMBUS_CHECK_IT_SOURCE(tmpcr1value, SMBUS_IT_ADDRI) != RESET) || (SMBUS_CHECK_IT_SOURCE(tmpcr1value, SMBUS_IT_STOPI) != RESET) || (SMBUS_CHECK_IT_SOURCE(tmpcr1value, SMBUS_IT_NACKI) != RESET)) && ((SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_ADDR) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_STOPF) != RESET) || (SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_AF) != RESET)))
- {
- if ((hsmbus->State & HAL_SMBUS_STATE_LISTEN) == HAL_SMBUS_STATE_LISTEN)
- {
- (void)SMBUS_Slave_ISR(hsmbus, tmpisrvalue);
- }
- }
-}
-
-/**
- * @brief Handle SMBUS error interrupt request.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-void HAL_SMBUS_ER_IRQHandler(SMBUS_HandleTypeDef *hsmbus)
-{
- SMBUS_ITErrorHandler(hsmbus);
-}
-
-/**
- * @brief Master Tx Transfer completed callback.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_MasterTxCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hsmbus);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_SMBUS_MasterTxCpltCallback() could be implemented in the user file
- */
-}
-
-/**
- * @brief Master Rx Transfer completed callback.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_MasterRxCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hsmbus);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_SMBUS_MasterRxCpltCallback() could be implemented in the user file
- */
-}
-
-/** @brief Slave Tx Transfer completed callback.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_SlaveTxCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hsmbus);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_SMBUS_SlaveTxCpltCallback() could be implemented in the user file
- */
-}
-
-/**
- * @brief Slave Rx Transfer completed callback.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_SlaveRxCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hsmbus);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_SMBUS_SlaveRxCpltCallback() could be implemented in the user file
- */
-}
-
-/**
- * @brief Slave Address Match callback.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param TransferDirection Master request Transfer Direction (Write/Read)
- * @param AddrMatchCode Address Match Code
- * @retval None
- */
-__weak void HAL_SMBUS_AddrCallback(SMBUS_HandleTypeDef *hsmbus, uint8_t TransferDirection, uint16_t AddrMatchCode)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hsmbus);
- UNUSED(TransferDirection);
- UNUSED(AddrMatchCode);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_SMBUS_AddrCallback() could be implemented in the user file
- */
-}
-
-/**
- * @brief Listen Complete callback.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_ListenCpltCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hsmbus);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_SMBUS_ListenCpltCallback() could be implemented in the user file
- */
-}
-
-/**
- * @brief SMBUS error callback.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval None
- */
-__weak void HAL_SMBUS_ErrorCallback(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hsmbus);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_SMBUS_ErrorCallback() could be implemented in the user file
- */
-}
-
-/**
- * @}
- */
-
-/** @defgroup SMBUS_Exported_Functions_Group3 Peripheral State and Errors functions
- * @brief Peripheral State and Errors functions
- *
-@verbatim
- ===============================================================================
- ##### Peripheral State and Errors functions #####
- ===============================================================================
- [..]
- This subsection permits to get in run-time the status of the peripheral
- and the data flow.
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Return the SMBUS handle state.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @retval HAL state
- */
-uint32_t HAL_SMBUS_GetState(SMBUS_HandleTypeDef *hsmbus)
-{
- /* Return SMBUS handle state */
- return hsmbus->State;
-}
-
-/**
-* @brief Return the SMBUS error code.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
-* @retval SMBUS Error Code
-*/
-uint32_t HAL_SMBUS_GetError(SMBUS_HandleTypeDef *hsmbus)
-{
- return hsmbus->ErrorCode;
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/** @addtogroup SMBUS_Private_Functions SMBUS Private Functions
- * @brief Data transfers Private functions
- * @{
- */
-
-/**
- * @brief Interrupt Sub-Routine which handle the Interrupt Flags Master Mode.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param StatusFlags Value of Interrupt Flags.
- * @retval HAL status
- */
-static HAL_StatusTypeDef SMBUS_Master_ISR(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t StatusFlags)
-{
- uint16_t DevAddress;
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_AF) != RESET)
- {
- /* Clear NACK Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF);
-
- /* Set corresponding Error Code */
- /* No need to generate STOP, it is automatically done */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ACKF;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the Error callback to inform upper layer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->ErrorCallback(hsmbus);
-#else
- HAL_SMBUS_ErrorCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- else if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_STOPF) != RESET)
- {
- /* Check and treat errors if errors occurs during STOP process */
- SMBUS_ITErrorHandler(hsmbus);
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
- if (hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- /* Disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX);
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
-
- /* Clear Configuration Register 2 */
- SMBUS_RESET_CR2(hsmbus);
-
- /* Flush remaining data in Fifo register in case of error occurs before TXEmpty */
- /* Disable the selected SMBUS peripheral */
- __HAL_SMBUS_DISABLE(hsmbus);
-
- hsmbus->PreviousState = HAL_SMBUS_STATE_READY;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* REenable the selected SMBUS peripheral */
- __HAL_SMBUS_ENABLE(hsmbus);
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->MasterTxCpltCallback(hsmbus);
-#else
- HAL_SMBUS_MasterTxCpltCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- else if (hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- /* Store Last receive data if any */
- if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_RXNE) != RESET)
- {
- /* Read data from RXDR */
- *hsmbus->pBuffPtr = (uint8_t)(hsmbus->Instance->RXDR);
-
- /* Increment Buffer pointer */
- hsmbus->pBuffPtr++;
-
- if ((hsmbus->XferSize > 0U))
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
-
- /* Disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX);
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
-
- /* Clear Configuration Register 2 */
- SMBUS_RESET_CR2(hsmbus);
-
- hsmbus->PreviousState = HAL_SMBUS_STATE_READY;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->MasterRxCpltCallback(hsmbus);
-#else
- HAL_SMBUS_MasterRxCpltCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- else
- {
- /* Nothing to do */
- }
- }
- else if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_RXNE) != RESET)
- {
- /* Read data from RXDR */
- *hsmbus->pBuffPtr = (uint8_t)(hsmbus->Instance->RXDR);
-
- /* Increment Buffer pointer */
- hsmbus->pBuffPtr++;
-
- /* Increment Size counter */
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- else if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_TXIS) != RESET)
- {
- /* Write data to TXDR */
- hsmbus->Instance->TXDR = *hsmbus->pBuffPtr;
-
- /* Increment Buffer pointer */
- hsmbus->pBuffPtr++;
-
- /* Increment Size counter */
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- else if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_TCR) != RESET)
- {
- if ((hsmbus->XferCount != 0U) && (hsmbus->XferSize == 0U))
- {
- DevAddress = (uint16_t)(hsmbus->Instance->CR2 & I2C_CR2_SADD);
-
- if (hsmbus->XferCount > MAX_NBYTE_SIZE)
- {
- SMBUS_TransferConfig(hsmbus, DevAddress, MAX_NBYTE_SIZE, (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)), SMBUS_NO_STARTSTOP);
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = hsmbus->XferCount;
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- /* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */
- /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
- if (SMBUS_GET_PEC_MODE(hsmbus) != 0UL)
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
- }
- else if ((hsmbus->XferCount == 0U) && (hsmbus->XferSize == 0U))
- {
- /* Call TxCpltCallback() if no stop mode is set */
- if (SMBUS_GET_STOP_MODE(hsmbus) != SMBUS_AUTOEND_MODE)
- {
- /* Call the corresponding callback to inform upper layer of End of Transfer */
- if (hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- /* Disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->MasterTxCpltCallback(hsmbus);
-#else
- HAL_SMBUS_MasterTxCpltCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- else if (hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->MasterRxCpltCallback(hsmbus);
-#else
- HAL_SMBUS_MasterRxCpltCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- else
- {
- /* Nothing to do */
- }
- }
- }
- else
- {
- /* Nothing to do */
- }
- }
- else if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_TC) != RESET)
- {
- if (hsmbus->XferCount == 0U)
- {
- /* Specific use case for Quick command */
- if (hsmbus->pBuffPtr == NULL)
- {
- /* Generate a Stop command */
- hsmbus->Instance->CR2 |= I2C_CR2_STOP;
- }
- /* Call TxCpltCallback() if no stop mode is set */
- else if (SMBUS_GET_STOP_MODE(hsmbus) != SMBUS_AUTOEND_MODE)
- {
- /* No Generate Stop, to permit restart mode */
- /* The stop will be done at the end of transfer, when SMBUS_AUTOEND_MODE enable */
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
- if (hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX)
- {
- /* Disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->MasterTxCpltCallback(hsmbus);
-#else
- HAL_SMBUS_MasterTxCpltCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- else if (hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX)
- {
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->MasterRxCpltCallback(hsmbus);
-#else
- HAL_SMBUS_MasterRxCpltCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- else
- {
- /* Nothing to do */
- }
- }
- else
- {
- /* Nothing to do */
- }
- }
- }
- else
- {
- /* Nothing to do */
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
-}
-/**
- * @brief Interrupt Sub-Routine which handle the Interrupt Flags Slave Mode.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param StatusFlags Value of Interrupt Flags.
- * @retval HAL status
- */
-static HAL_StatusTypeDef SMBUS_Slave_ISR(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t StatusFlags)
-{
- uint8_t TransferDirection;
- uint16_t SlaveAddrCode;
-
- /* Process Locked */
- __HAL_LOCK(hsmbus);
-
- if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_AF) != RESET)
- {
- /* Check that SMBUS transfer finished */
- /* if yes, normal usecase, a NACK is sent by the HOST when Transfer is finished */
- /* Mean XferCount == 0*/
- /* So clear Flag NACKF only */
- if (hsmbus->XferCount == 0U)
- {
- /* Clear NACK Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
- }
- else
- {
- /* if no, error usecase, a Non-Acknowledge of last Data is generated by the HOST*/
- /* Clear NACK Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF);
-
- /* Set HAL State to "Idle" State, mean to LISTEN state */
- /* So reset Slave Busy state */
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_TX);
- hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_RX);
-
- /* Disable RX/TX Interrupts, keep only ADDR Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX | SMBUS_IT_TX);
-
- /* Set ErrorCode corresponding to a Non-Acknowledge */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ACKF;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the Error callback to inform upper layer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->ErrorCallback(hsmbus);
-#else
- HAL_SMBUS_ErrorCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- }
- else if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_ADDR) != RESET)
- {
- TransferDirection = (uint8_t)(SMBUS_GET_DIR(hsmbus));
- SlaveAddrCode = (uint16_t)(SMBUS_GET_ADDR_MATCH(hsmbus));
-
- /* Disable ADDR interrupt to prevent multiple ADDRInterrupt*/
- /* Other ADDRInterrupt will be treat in next Listen usecase */
- __HAL_SMBUS_DISABLE_IT(hsmbus, SMBUS_IT_ADDRI);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call Slave Addr callback */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->AddrCallback(hsmbus, TransferDirection, SlaveAddrCode);
-#else
- HAL_SMBUS_AddrCallback(hsmbus, TransferDirection, SlaveAddrCode);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- else if ((SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_RXNE) != RESET) || (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_TCR) != RESET))
- {
- if ((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_RX) == HAL_SMBUS_STATE_SLAVE_BUSY_RX)
- {
- /* Read data from RXDR */
- *hsmbus->pBuffPtr = (uint8_t)(hsmbus->Instance->RXDR);
-
- /* Increment Buffer pointer */
- hsmbus->pBuffPtr++;
-
- hsmbus->XferSize--;
- hsmbus->XferCount--;
-
- if (hsmbus->XferCount == 1U)
- {
- /* Receive last Byte, can be PEC byte in case of PEC BYTE enabled */
- /* or only the last Byte of Transfer */
- /* So reset the RELOAD bit mode */
- hsmbus->XferOptions &= ~SMBUS_RELOAD_MODE;
- SMBUS_TransferConfig(hsmbus, 0, 1, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- }
- else if (hsmbus->XferCount == 0U)
- {
- /* Last Byte is received, disable Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX);
-
- /* Remove HAL_SMBUS_STATE_SLAVE_BUSY_RX, keep only HAL_SMBUS_STATE_LISTEN */
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_RX);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->SlaveRxCpltCallback(hsmbus);
-#else
- HAL_SMBUS_SlaveRxCpltCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- else
- {
- /* Set Reload for next Bytes */
- SMBUS_TransferConfig(hsmbus, 0, 1, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_NO_STARTSTOP);
-
- /* Ack last Byte Read */
- hsmbus->Instance->CR2 &= ~I2C_CR2_NACK;
- }
- }
- else if ((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_TX) == HAL_SMBUS_STATE_SLAVE_BUSY_TX)
- {
- if ((hsmbus->XferCount != 0U) && (hsmbus->XferSize == 0U))
- {
- if (hsmbus->XferCount > MAX_NBYTE_SIZE)
- {
- SMBUS_TransferConfig(hsmbus, 0, MAX_NBYTE_SIZE, (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)), SMBUS_NO_STARTSTOP);
- hsmbus->XferSize = MAX_NBYTE_SIZE;
- }
- else
- {
- hsmbus->XferSize = hsmbus->XferCount;
- SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
- /* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */
- /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
- if (SMBUS_GET_PEC_MODE(hsmbus) != 0UL)
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
- }
- }
- else
- {
- /* Nothing to do */
- }
- }
- else if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_TXIS) != RESET)
- {
- /* Write data to TXDR only if XferCount not reach "0" */
- /* A TXIS flag can be set, during STOP treatment */
- /* Check if all Data have already been sent */
- /* If it is the case, this last write in TXDR is not sent, correspond to a dummy TXIS event */
- if (hsmbus->XferCount > 0U)
- {
- /* Write data to TXDR */
- hsmbus->Instance->TXDR = *hsmbus->pBuffPtr;
-
- /* Increment Buffer pointer */
- hsmbus->pBuffPtr++;
-
- hsmbus->XferCount--;
- hsmbus->XferSize--;
- }
-
- if (hsmbus->XferCount == 0U)
- {
- /* Last Byte is Transmitted */
- /* Remove HAL_SMBUS_STATE_SLAVE_BUSY_TX, keep only HAL_SMBUS_STATE_LISTEN */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX);
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_TX);
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the corresponding callback to inform upper layer of End of Transfer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->SlaveTxCpltCallback(hsmbus);
-#else
- HAL_SMBUS_SlaveTxCpltCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- }
- else
- {
- /* Nothing to do */
- }
-
- /* Check if STOPF is set */
- if (SMBUS_CHECK_FLAG(StatusFlags, SMBUS_FLAG_STOPF) != RESET)
- {
- if ((hsmbus->State & HAL_SMBUS_STATE_LISTEN) == HAL_SMBUS_STATE_LISTEN)
- {
- /* Store Last receive data if any */
- if (__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_RXNE) != RESET)
- {
- /* Read data from RXDR */
- *hsmbus->pBuffPtr = (uint8_t)(hsmbus->Instance->RXDR);
-
- /* Increment Buffer pointer */
- hsmbus->pBuffPtr++;
-
- if ((hsmbus->XferSize > 0U))
- {
- hsmbus->XferSize--;
- hsmbus->XferCount--;
- }
- }
-
- /* Disable RX and TX Interrupts */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX | SMBUS_IT_TX);
-
- /* Disable ADDR Interrupt */
- SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR);
-
- /* Disable Address Acknowledge */
- hsmbus->Instance->CR2 |= I2C_CR2_NACK;
-
- /* Clear Configuration Register 2 */
- SMBUS_RESET_CR2(hsmbus);
-
- /* Clear STOP Flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF);
-
- /* Clear ADDR flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ADDR);
-
- hsmbus->XferOptions = 0;
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- /* Call the Listen Complete callback, to inform upper layer of the end of Listen usecase */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->ListenCpltCallback(hsmbus);
-#else
- HAL_SMBUS_ListenCpltCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_OK;
-}
-/**
- * @brief Manage the enabling of Interrupts.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param InterruptRequest Value of @ref SMBUS_Interrupt_configuration_definition.
- * @retval HAL status
- */
-static void SMBUS_Enable_IRQ(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t InterruptRequest)
-{
- uint32_t tmpisr = 0UL;
-
- if ((InterruptRequest & SMBUS_IT_ALERT) == SMBUS_IT_ALERT)
- {
- /* Enable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
-
- if ((InterruptRequest & SMBUS_IT_ADDR) == SMBUS_IT_ADDR)
- {
- /* Enable ADDR, STOP interrupt */
- tmpisr |= SMBUS_IT_ADDRI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_ERRI;
- }
-
- if ((InterruptRequest & SMBUS_IT_TX) == SMBUS_IT_TX)
- {
- /* Enable ERR, TC, STOP, NACK, RXI interrupt */
- tmpisr |= SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_TXI;
- }
-
- if ((InterruptRequest & SMBUS_IT_RX) == SMBUS_IT_RX)
- {
- /* Enable ERR, TC, STOP, NACK, TXI interrupt */
- tmpisr |= SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_RXI;
- }
-
- /* Enable interrupts only at the end */
- /* to avoid the risk of SMBUS interrupt handle execution before */
- /* all interrupts requested done */
- __HAL_SMBUS_ENABLE_IT(hsmbus, tmpisr);
-}
-/**
- * @brief Manage the disabling of Interrupts.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param InterruptRequest Value of @ref SMBUS_Interrupt_configuration_definition.
- * @retval HAL status
- */
-static void SMBUS_Disable_IRQ(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t InterruptRequest)
-{
- uint32_t tmpisr = 0UL;
- uint32_t tmpstate = hsmbus->State;
-
- if ((tmpstate == HAL_SMBUS_STATE_READY) && ((InterruptRequest & SMBUS_IT_ALERT) == SMBUS_IT_ALERT))
- {
- /* Disable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
-
- if ((InterruptRequest & SMBUS_IT_TX) == SMBUS_IT_TX)
- {
- /* Disable TC, STOP, NACK and TXI interrupt */
- tmpisr |= SMBUS_IT_TCI | SMBUS_IT_TXI;
-
- if ((SMBUS_GET_ALERT_ENABLED(hsmbus) == 0UL)
- && ((tmpstate & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN))
- {
- /* Disable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
-
- if ((tmpstate & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN)
- {
- /* Disable STOP and NACK interrupt */
- tmpisr |= SMBUS_IT_STOPI | SMBUS_IT_NACKI;
- }
- }
-
- if ((InterruptRequest & SMBUS_IT_RX) == SMBUS_IT_RX)
- {
- /* Disable TC, STOP, NACK and RXI interrupt */
- tmpisr |= SMBUS_IT_TCI | SMBUS_IT_RXI;
-
- if ((SMBUS_GET_ALERT_ENABLED(hsmbus) == 0UL)
- && ((tmpstate & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN))
- {
- /* Disable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
-
- if ((tmpstate & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN)
- {
- /* Disable STOP and NACK interrupt */
- tmpisr |= SMBUS_IT_STOPI | SMBUS_IT_NACKI;
- }
- }
-
- if ((InterruptRequest & SMBUS_IT_ADDR) == SMBUS_IT_ADDR)
- {
- /* Disable ADDR, STOP and NACK interrupt */
- tmpisr |= SMBUS_IT_ADDRI | SMBUS_IT_STOPI | SMBUS_IT_NACKI;
-
- if (SMBUS_GET_ALERT_ENABLED(hsmbus) == 0UL)
- {
- /* Disable ERR interrupt */
- tmpisr |= SMBUS_IT_ERRI;
- }
- }
-
- /* Disable interrupts only at the end */
- /* to avoid a breaking situation like at "t" time */
- /* all disable interrupts request are not done */
- __HAL_SMBUS_DISABLE_IT(hsmbus, tmpisr);
-}
-
-/**
- * @brief SMBUS interrupts error handler.
- * @param hsmbus SMBUS handle.
- * @retval None
- */
-static void SMBUS_ITErrorHandler(struct __SMBUS_HandleTypeDef *hsmbus)
-{
- uint32_t itflags = READ_REG(hsmbus->Instance->ISR);
- uint32_t itsources = READ_REG(hsmbus->Instance->CR1);
- uint32_t tmpstate;
- uint32_t tmperror;
-
- /* SMBUS Bus error interrupt occurred ------------------------------------*/
- if (((itflags & SMBUS_FLAG_BERR) == SMBUS_FLAG_BERR) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_BERR;
-
- /* Clear BERR flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_BERR);
- }
-
- /* SMBUS Over-Run/Under-Run interrupt occurred ----------------------------------------*/
- if (((itflags & SMBUS_FLAG_OVR) == SMBUS_FLAG_OVR) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_OVR;
-
- /* Clear OVR flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_OVR);
- }
-
- /* SMBUS Arbitration Loss error interrupt occurred ------------------------------------*/
- if (((itflags & SMBUS_FLAG_ARLO) == SMBUS_FLAG_ARLO) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ARLO;
-
- /* Clear ARLO flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ARLO);
- }
-
- /* SMBUS Timeout error interrupt occurred ---------------------------------------------*/
- if (((itflags & SMBUS_FLAG_TIMEOUT) == SMBUS_FLAG_TIMEOUT) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_BUSTIMEOUT;
-
- /* Clear TIMEOUT flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_TIMEOUT);
- }
-
- /* SMBUS Alert error interrupt occurred -----------------------------------------------*/
- if (((itflags & SMBUS_FLAG_ALERT) == SMBUS_FLAG_ALERT) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ALERT;
-
- /* Clear ALERT flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ALERT);
- }
-
- /* SMBUS Packet Error Check error interrupt occurred ----------------------------------*/
- if (((itflags & SMBUS_FLAG_PECERR) == SMBUS_FLAG_PECERR) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
- {
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_PECERR;
-
- /* Clear PEC error flag */
- __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_PECERR);
- }
-
- /* Store current volatile hsmbus->State, misra rule */
- tmperror = hsmbus->ErrorCode;
-
- /* Call the Error Callback in case of Error detected */
- if ((tmperror != HAL_SMBUS_ERROR_NONE) && (tmperror != HAL_SMBUS_ERROR_ACKF))
- {
- /* Do not Reset the HAL state in case of ALERT error */
- if ((tmperror & HAL_SMBUS_ERROR_ALERT) != HAL_SMBUS_ERROR_ALERT)
- {
- /* Store current volatile hsmbus->State, misra rule */
- tmpstate = hsmbus->State;
-
- if (((tmpstate & HAL_SMBUS_STATE_SLAVE_BUSY_TX) == HAL_SMBUS_STATE_SLAVE_BUSY_TX)
- || ((tmpstate & HAL_SMBUS_STATE_SLAVE_BUSY_RX) == HAL_SMBUS_STATE_SLAVE_BUSY_RX))
- {
- /* Reset only HAL_SMBUS_STATE_SLAVE_BUSY_XX */
- /* keep HAL_SMBUS_STATE_LISTEN if set */
- hsmbus->PreviousState = HAL_SMBUS_STATE_READY;
- hsmbus->State = HAL_SMBUS_STATE_LISTEN;
- }
- }
-
- /* Call the Error callback to inform upper layer */
-#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- hsmbus->ErrorCallback(hsmbus);
-#else
- HAL_SMBUS_ErrorCallback(hsmbus);
-#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
- }
-}
-
-/**
- * @brief Handle SMBUS Communication Timeout.
- * @param hsmbus Pointer to a SMBUS_HandleTypeDef structure that contains
- * the configuration information for the specified SMBUS.
- * @param Flag Specifies the SMBUS flag to check.
- * @param Status The new Flag status (SET or RESET).
- * @param Timeout Timeout duration
- * @retval HAL status
- */
-static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(struct __SMBUS_HandleTypeDef *hsmbus, uint32_t Flag, FlagStatus Status, uint32_t Timeout)
-{
- uint32_t tickstart = HAL_GetTick();
-
- /* Wait until flag is set */
- while ((FlagStatus)(__HAL_SMBUS_GET_FLAG(hsmbus, Flag)) == Status)
- {
- /* Check for the Timeout */
- if (Timeout != HAL_MAX_DELAY)
- {
- if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0UL))
- {
- hsmbus->PreviousState = hsmbus->State;
- hsmbus->State = HAL_SMBUS_STATE_READY;
-
- /* Update SMBUS error code */
- hsmbus->ErrorCode |= HAL_SMBUS_ERROR_HALTIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hsmbus);
-
- return HAL_ERROR;
- }
- }
- }
-
- return HAL_OK;
-}
-
-/**
- * @brief Handle SMBUSx communication when starting transfer or during transfer (TC or TCR flag are set).
- * @param hsmbus SMBUS handle.
- * @param DevAddress specifies the slave address to be programmed.
- * @param Size specifies the number of bytes to be programmed.
- * This parameter must be a value between 0 and 255.
- * @param Mode New state of the SMBUS START condition generation.
- * This parameter can be one or a combination of the following values:
- * @arg @ref SMBUS_RELOAD_MODE Enable Reload mode.
- * @arg @ref SMBUS_AUTOEND_MODE Enable Automatic end mode.
- * @arg @ref SMBUS_SOFTEND_MODE Enable Software end mode and Reload mode.
- * @arg @ref SMBUS_SENDPEC_MODE Enable Packet Error Calculation mode.
- * @param Request New state of the SMBUS START condition generation.
- * This parameter can be one of the following values:
- * @arg @ref SMBUS_NO_STARTSTOP Don't Generate stop and start condition.
- * @arg @ref SMBUS_GENERATE_STOP Generate stop condition (Size should be set to 0).
- * @arg @ref SMBUS_GENERATE_START_READ Generate Restart for read request.
- * @arg @ref SMBUS_GENERATE_START_WRITE Generate Restart for write request.
- * @retval None
- */
-static void SMBUS_TransferConfig(struct __SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request)
-{
- /* Check the parameters */
- assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance));
- assert_param(IS_SMBUS_TRANSFER_MODE(Mode));
- assert_param(IS_SMBUS_TRANSFER_REQUEST(Request));
-
- /* update CR2 register */
- MODIFY_REG(hsmbus->Instance->CR2, ((I2C_CR2_SADD | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_AUTOEND | (I2C_CR2_RD_WRN & (uint32_t)(Request >> (31UL - I2C_CR2_RD_WRN_Pos))) | I2C_CR2_START | I2C_CR2_STOP | I2C_CR2_PECBYTE)), \
- (uint32_t)(((uint32_t)DevAddress & I2C_CR2_SADD) | (((uint32_t)Size << I2C_CR2_NBYTES_Pos) & I2C_CR2_NBYTES) | (uint32_t)Mode | (uint32_t)Request));
-}
-
-/**
- * @brief Convert SMBUSx OTHER_xxx XferOptions to functionnal XferOptions.
- * @param hsmbus SMBUS handle.
- * @retval None
- */
-static void SMBUS_ConvertOtherXferOptions(struct __SMBUS_HandleTypeDef *hsmbus)
-{
- /* if user set XferOptions to SMBUS_OTHER_FRAME_NO_PEC */
- /* it request implicitly to generate a restart condition */
- /* set XferOptions to SMBUS_FIRST_FRAME */
- if (hsmbus->XferOptions == SMBUS_OTHER_FRAME_NO_PEC)
- {
- hsmbus->XferOptions = SMBUS_FIRST_FRAME;
- }
- /* else if user set XferOptions to SMBUS_OTHER_FRAME_WITH_PEC */
- /* it request implicitly to generate a restart condition */
- /* set XferOptions to SMBUS_FIRST_FRAME | SMBUS_SENDPEC_MODE */
- else if (hsmbus->XferOptions == SMBUS_OTHER_FRAME_WITH_PEC)
- {
- hsmbus->XferOptions = SMBUS_FIRST_FRAME | SMBUS_SENDPEC_MODE;
- }
- /* else if user set XferOptions to SMBUS_OTHER_AND_LAST_FRAME_NO_PEC */
- /* it request implicitly to generate a restart condition */
- /* then generate a stop condition at the end of transfer */
- /* set XferOptions to SMBUS_FIRST_AND_LAST_FRAME_NO_PEC */
- else if (hsmbus->XferOptions == SMBUS_OTHER_AND_LAST_FRAME_NO_PEC)
- {
- hsmbus->XferOptions = SMBUS_FIRST_AND_LAST_FRAME_NO_PEC;
- }
- /* else if user set XferOptions to SMBUS_OTHER_AND_LAST_FRAME_WITH_PEC */
- /* it request implicitly to generate a restart condition */
- /* then generate a stop condition at the end of transfer */
- /* set XferOptions to SMBUS_FIRST_AND_LAST_FRAME_WITH_PEC */
- else if (hsmbus->XferOptions == SMBUS_OTHER_AND_LAST_FRAME_WITH_PEC)
- {
- hsmbus->XferOptions = SMBUS_FIRST_AND_LAST_FRAME_WITH_PEC;
- }
- else
- {
- /* Nothing to do */
- }
-}
-/**
- * @}
- */
-
-#endif /* HAL_SMBUS_MODULE_ENABLED */
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|