From 6ab94e0b318884bbcb95e2ea3835f951502e1d99 Mon Sep 17 00:00:00 2001 From: jaseg Date: Wed, 14 Oct 2020 12:47:28 +0200 Subject: Move firmware into subdirectory --- .../Src/stm32f0xx_hal_pwr_ex.c | 274 --------------------- 1 file changed, 274 deletions(-) delete mode 100644 hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_pwr_ex.c (limited to 'hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_pwr_ex.c') diff --git a/hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_pwr_ex.c b/hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_pwr_ex.c deleted file mode 100644 index c14370b..0000000 --- a/hid-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_pwr_ex.c +++ /dev/null @@ -1,274 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f0xx_hal_pwr_ex.c - * @author MCD Application Team - * @brief Extended PWR HAL module driver. - * This file provides firmware functions to manage the following - * functionalities of the Power Controller (PWR) peripheral: - * + Extended Initialization and de-initialization functions - * + Extended Peripheral Control functions - * - ****************************************************************************** - * @attention - * - *

© Copyright (c) 2016 STMicroelectronics. - * All rights reserved.

- * - * This software component is licensed by ST under BSD 3-Clause license, - * the "License"; You may not use this file except in compliance with the - * License. You may obtain a copy of the License at: - * opensource.org/licenses/BSD-3-Clause - * - ****************************************************************************** - */ - -/* Includes ------------------------------------------------------------------*/ -#include "stm32f0xx_hal.h" - -/** @addtogroup STM32F0xx_HAL_Driver - * @{ - */ - -/** @defgroup PWREx PWREx - * @brief PWREx HAL module driver - * @{ - */ - -#ifdef HAL_PWR_MODULE_ENABLED - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/** @defgroup PWREx_Private_Constants PWREx Private Constants - * @{ - */ -#define PVD_MODE_IT (0x00010000U) -#define PVD_MODE_EVT (0x00020000U) -#define PVD_RISING_EDGE (0x00000001U) -#define PVD_FALLING_EDGE (0x00000002U) -/** - * @} - */ - -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ -/* Private function prototypes -----------------------------------------------*/ -/* Exported functions ---------------------------------------------------------*/ - -/** @defgroup PWREx_Exported_Functions PWREx Exported Functions - * @{ - */ - -/** @defgroup PWREx_Exported_Functions_Group1 Peripheral Extended Control Functions - * @brief Extended Peripheral Control functions - * -@verbatim - - =============================================================================== - ##### Peripheral extended control functions ##### - =============================================================================== - - *** PVD configuration *** - ========================= - [..] - (+) The PVD is used to monitor the VDD power supply by comparing it to a - threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR). - (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower - than the PVD threshold. This event is internally connected to the EXTI - line16 and can generate an interrupt if enabled. This is done through - HAL_PWR_ConfigPVD(), HAL_PWR_EnablePVD() functions. - (+) The PVD is stopped in Standby mode. - -@- PVD is not available on STM32F030x4/x6/x8 - - *** VDDIO2 Monitor Configuration *** - ==================================== - [..] - (+) VDDIO2 monitor is used to monitor the VDDIO2 power supply by comparing it - to VREFInt Voltage - (+) This monitor is internally connected to the EXTI line31 - and can generate an interrupt if enabled. This is done through - HAL_PWREx_EnableVddio2Monitor() function. - -@- VDDIO2 is available on STM32F07x/09x/04x - -@endverbatim - * @{ - */ - -#if defined (STM32F031x6) || defined (STM32F051x8) || \ - defined (STM32F071xB) || defined (STM32F091xC) || \ - defined (STM32F042x6) || defined (STM32F072xB) -/** - * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD). - * @param sConfigPVD pointer to an PWR_PVDTypeDef structure that contains the configuration - * information for the PVD. - * @note Refer to the electrical characteristics of your device datasheet for - * more details about the voltage threshold corresponding to each - * detection level. - * @retval None - */ -void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD) -{ - /* Check the parameters */ - assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel)); - assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode)); - - /* Set PLS[7:5] bits according to PVDLevel value */ - MODIFY_REG(PWR->CR, PWR_CR_PLS, sConfigPVD->PVDLevel); - - /* Clear any previous config. Keep it clear if no event or IT mode is selected */ - __HAL_PWR_PVD_EXTI_DISABLE_EVENT(); - __HAL_PWR_PVD_EXTI_DISABLE_IT(); - __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); - - /* Configure interrupt mode */ - if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT) - { - __HAL_PWR_PVD_EXTI_ENABLE_IT(); - } - - /* Configure event mode */ - if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT) - { - __HAL_PWR_PVD_EXTI_ENABLE_EVENT(); - } - - /* Configure the edge */ - if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE) - { - __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE(); - } - - if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE) - { - __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); - } -} - -/** - * @brief Enables the Power Voltage Detector(PVD). - * @retval None - */ -void HAL_PWR_EnablePVD(void) -{ - PWR->CR |= (uint32_t)PWR_CR_PVDE; -} - -/** - * @brief Disables the Power Voltage Detector(PVD). - * @retval None - */ -void HAL_PWR_DisablePVD(void) -{ - PWR->CR &= ~((uint32_t)PWR_CR_PVDE); -} - -/** - * @brief This function handles the PWR PVD interrupt request. - * @note This API should be called under the PVD_IRQHandler() or PVD_VDDIO2_IRQHandler(). - * @retval None - */ -void HAL_PWR_PVD_IRQHandler(void) -{ - /* Check PWR exti flag */ - if(__HAL_PWR_PVD_EXTI_GET_FLAG() != RESET) - { - /* PWR PVD interrupt user callback */ - HAL_PWR_PVDCallback(); - - /* Clear PWR Exti pending bit */ - __HAL_PWR_PVD_EXTI_CLEAR_FLAG(); - } -} - -/** - * @brief PWR PVD interrupt callback - * @retval None - */ -__weak void HAL_PWR_PVDCallback(void) -{ - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_PWR_PVDCallback could be implemented in the user file - */ -} - -#endif /* defined (STM32F031x6) || defined (STM32F051x8) || */ - /* defined (STM32F071xB) || defined (STM32F091xC) || */ - /* defined (STM32F042x6) || defined (STM32F072xB) */ - -#if defined (STM32F042x6) || defined (STM32F048xx) || \ - defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \ - defined (STM32F091xC) || defined (STM32F098xx) -/** - * @brief Enable VDDIO2 monitor: enable Exti 31 and falling edge detection. - * @note If Exti 31 is enable correlty and VDDIO2 voltage goes below Vrefint, - an interrupt is generated Irq line 1. - NVIS has to be enable by user. - * @retval None - */ -void HAL_PWREx_EnableVddio2Monitor(void) -{ - __HAL_PWR_VDDIO2_EXTI_ENABLE_IT(); - __HAL_PWR_VDDIO2_EXTI_ENABLE_FALLING_EDGE(); -} - -/** - * @brief Disable the Vddio2 Monitor. - * @retval None - */ -void HAL_PWREx_DisableVddio2Monitor(void) -{ - __HAL_PWR_VDDIO2_EXTI_DISABLE_IT(); - __HAL_PWR_VDDIO2_EXTI_DISABLE_FALLING_EDGE(); - -} - -/** - * @brief This function handles the PWR Vddio2 monitor interrupt request. - * @note This API should be called under the VDDIO2_IRQHandler() PVD_VDDIO2_IRQHandler(). - * @retval None - */ -void HAL_PWREx_Vddio2Monitor_IRQHandler(void) -{ - /* Check PWR exti flag */ - if(__HAL_PWR_VDDIO2_EXTI_GET_FLAG() != RESET) - { - /* PWR Vddio2 monitor interrupt user callback */ - HAL_PWREx_Vddio2MonitorCallback(); - - /* Clear PWR Exti pending bit */ - __HAL_PWR_VDDIO2_EXTI_CLEAR_FLAG(); - } -} - -/** - * @brief PWR Vddio2 Monitor interrupt callback - * @retval None - */ -__weak void HAL_PWREx_Vddio2MonitorCallback(void) -{ - /* NOTE : This function Should not be modified, when the callback is needed, - the HAL_PWREx_Vddio2MonitorCallback could be implemented in the user file - */ -} - -#endif /* defined (STM32F042x6) || defined (STM32F048xx) || \ - defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \ - defined (STM32F091xC) || defined (STM32F098xx) */ - -/** - * @} - */ - -/** - * @} - */ - -#endif /* HAL_PWR_MODULE_ENABLED */ -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit