From 6ab94e0b318884bbcb95e2ea3835f951502e1d99 Mon Sep 17 00:00:00 2001 From: jaseg Date: Wed, 14 Oct 2020 12:47:28 +0200 Subject: Move firmware into subdirectory --- .../Src/stm32f0xx_hal_cortex.c | 341 +++++++++++++++++++++ 1 file changed, 341 insertions(+) create mode 100644 fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_cortex.c (limited to 'fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_cortex.c') diff --git a/fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_cortex.c b/fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_cortex.c new file mode 100644 index 0000000..cbe3f5b --- /dev/null +++ b/fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Src/stm32f0xx_hal_cortex.c @@ -0,0 +1,341 @@ +/** + ****************************************************************************** + * @file stm32f0xx_hal_cortex.c + * @author MCD Application Team + * @brief CORTEX HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the CORTEX: + * + Initialization and de-initialization functions + * + Peripheral Control functions + * + * @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + + [..] + *** How to configure Interrupts using CORTEX HAL driver *** + =========================================================== + [..] + This section provides functions allowing to configure the NVIC interrupts (IRQ). + The Cortex-M0 exceptions are managed by CMSIS functions. + (#) Enable and Configure the priority of the selected IRQ Channels. + The priority can be 0..3. + + -@- Lower priority values gives higher priority. + -@- Priority Order: + (#@) Lowest priority. + (#@) Lowest hardware priority (IRQn position). + + (#) Configure the priority of the selected IRQ Channels using HAL_NVIC_SetPriority() + + (#) Enable the selected IRQ Channels using HAL_NVIC_EnableIRQ() + + -@- Negative value of IRQn_Type are not allowed. + + + [..] + *** How to configure Systick using CORTEX HAL driver *** + ======================================================== + [..] + Setup SysTick Timer for time base. + + (+) The HAL_SYSTICK_Config()function calls the SysTick_Config() function which + is a CMSIS function that: + (++) Configures the SysTick Reload register with value passed as function parameter. + (++) Configures the SysTick IRQ priority to the lowest value (0x03). + (++) Resets the SysTick Counter register. + (++) Configures the SysTick Counter clock source to be Core Clock Source (HCLK). + (++) Enables the SysTick Interrupt. + (++) Starts the SysTick Counter. + + (+) You can change the SysTick Clock source to be HCLK_Div8 by calling the macro + HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK_DIV8) just after the + HAL_SYSTICK_Config() function call. The HAL_SYSTICK_CLKSourceConfig() macro is defined + inside the stm32f0xx_hal_cortex.h file. + + (+) You can change the SysTick IRQ priority by calling the + HAL_NVIC_SetPriority(SysTick_IRQn,...) function just after the HAL_SYSTICK_Config() function + call. The HAL_NVIC_SetPriority() call the NVIC_SetPriority() function which is a CMSIS function. + + (+) To adjust the SysTick time base, use the following formula: + + Reload Value = SysTick Counter Clock (Hz) x Desired Time base (s) + (++) Reload Value is the parameter to be passed for HAL_SYSTICK_Config() function + (++) Reload Value should not exceed 0xFFFFFF + + @endverbatim + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f0xx_hal.h" + +/** @addtogroup STM32F0xx_HAL_Driver + * @{ + */ + +/** @defgroup CORTEX CORTEX + * @brief CORTEX CORTEX HAL module driver + * @{ + */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Exported functions ---------------------------------------------------------*/ + +/** @defgroup CORTEX_Exported_Functions CORTEX Exported Functions + * @{ + */ + + +/** @defgroup CORTEX_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + ============================================================================== + ##### Initialization and de-initialization functions ##### + ============================================================================== + [..] + This section provides the CORTEX HAL driver functions allowing to configure Interrupts + Systick functionalities + +@endverbatim + * @{ + */ + +/** + * @brief Sets the priority of an interrupt. + * @param IRQn External interrupt number . + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to stm32f0xx.h file) + * @param PreemptPriority The preemption priority for the IRQn channel. + * This parameter can be a value between 0 and 3. + * A lower priority value indicates a higher priority + * @param SubPriority the subpriority level for the IRQ channel. + * with stm32f0xx devices, this parameter is a dummy value and it is ignored, because + * no subpriority supported in Cortex M0 based products. + * @retval None + */ +void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority) +{ + /* Check the parameters */ + assert_param(IS_NVIC_PREEMPTION_PRIORITY(PreemptPriority)); + NVIC_SetPriority(IRQn,PreemptPriority); +} + +/** + * @brief Enables a device specific interrupt in the NVIC interrupt controller. + * @note To configure interrupts priority correctly, the NVIC_PriorityGroupConfig() + * function should be called before. + * @param IRQn External interrupt number. + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h)) + * @retval None + */ +void HAL_NVIC_EnableIRQ(IRQn_Type IRQn) +{ + /* Check the parameters */ + assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + + /* Enable interrupt */ + NVIC_EnableIRQ(IRQn); +} + +/** + * @brief Disables a device specific interrupt in the NVIC interrupt controller. + * @param IRQn External interrupt number. + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h)) + * @retval None + */ +void HAL_NVIC_DisableIRQ(IRQn_Type IRQn) +{ + /* Check the parameters */ + assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + + /* Disable interrupt */ + NVIC_DisableIRQ(IRQn); +} + +/** + * @brief Initiates a system reset request to reset the MCU. + * @retval None + */ +void HAL_NVIC_SystemReset(void) +{ + /* System Reset */ + NVIC_SystemReset(); +} + +/** + * @brief Initializes the System Timer and its interrupt, and starts the System Tick Timer. + * Counter is in free running mode to generate periodic interrupts. + * @param TicksNumb Specifies the ticks Number of ticks between two interrupts. + * @retval status: - 0 Function succeeded. + * - 1 Function failed. + */ +uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb) +{ + return SysTick_Config(TicksNumb); +} +/** + * @} + */ + +/** @defgroup CORTEX_Exported_Functions_Group2 Peripheral Control functions + * @brief Cortex control functions + * +@verbatim + ============================================================================== + ##### Peripheral Control functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to control the CORTEX + (NVIC, SYSTICK) functionalities. + + +@endverbatim + * @{ + */ + + +/** + * @brief Gets the priority of an interrupt. + * @param IRQn External interrupt number. + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h)) + * @retval None + */ +uint32_t HAL_NVIC_GetPriority(IRQn_Type IRQn) +{ + /* Get priority for Cortex-M system or device specific interrupts */ + return NVIC_GetPriority(IRQn); +} + +/** + * @brief Sets Pending bit of an external interrupt. + * @param IRQn External interrupt number + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h)) + * @retval None + */ +void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn) +{ + /* Check the parameters */ + assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + + /* Set interrupt pending */ + NVIC_SetPendingIRQ(IRQn); +} + +/** + * @brief Gets Pending Interrupt (reads the pending register in the NVIC + * and returns the pending bit for the specified interrupt). + * @param IRQn External interrupt number. + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h)) + * @retval status: - 0 Interrupt status is not pending. + * - 1 Interrupt status is pending. + */ +uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn) +{ + /* Check the parameters */ + assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + + /* Return 1 if pending else 0 */ + return NVIC_GetPendingIRQ(IRQn); +} + +/** + * @brief Clears the pending bit of an external interrupt. + * @param IRQn External interrupt number. + * This parameter can be an enumerator of IRQn_Type enumeration + * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f0xxxx.h)) + * @retval None + */ +void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn) +{ + /* Check the parameters */ + assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); + + /* Clear pending interrupt */ + NVIC_ClearPendingIRQ(IRQn); +} + +/** + * @brief Configures the SysTick clock source. + * @param CLKSource specifies the SysTick clock source. + * This parameter can be one of the following values: + * @arg SYSTICK_CLKSOURCE_HCLK_DIV8: AHB clock divided by 8 selected as SysTick clock source. + * @arg SYSTICK_CLKSOURCE_HCLK: AHB clock selected as SysTick clock source. + * @retval None + */ +void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource) +{ + /* Check the parameters */ + assert_param(IS_SYSTICK_CLK_SOURCE(CLKSource)); + if (CLKSource == SYSTICK_CLKSOURCE_HCLK) + { + SysTick->CTRL |= SYSTICK_CLKSOURCE_HCLK; + } + else + { + SysTick->CTRL &= ~SYSTICK_CLKSOURCE_HCLK; + } +} + +/** + * @brief This function handles SYSTICK interrupt request. + * @retval None + */ +void HAL_SYSTICK_IRQHandler(void) +{ + HAL_SYSTICK_Callback(); +} + +/** + * @brief SYSTICK callback. + * @retval None + */ +__weak void HAL_SYSTICK_Callback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SYSTICK_Callback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_CORTEX_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit