From 6ab94e0b318884bbcb95e2ea3835f951502e1d99 Mon Sep 17 00:00:00 2001 From: jaseg Date: Wed, 14 Oct 2020 12:47:28 +0200 Subject: Move firmware into subdirectory --- .../STM32F0xx_HAL_Driver/Inc/stm32f0xx_ll_i2c.h | 2230 ++++++++++++++++++++ 1 file changed, 2230 insertions(+) create mode 100644 fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_ll_i2c.h (limited to 'fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_ll_i2c.h') diff --git a/fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_ll_i2c.h b/fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_ll_i2c.h new file mode 100644 index 0000000..76956ce --- /dev/null +++ b/fw/cdc-dials/Drivers/STM32F0xx_HAL_Driver/Inc/stm32f0xx_ll_i2c.h @@ -0,0 +1,2230 @@ +/** + ****************************************************************************** + * @file stm32f0xx_ll_i2c.h + * @author MCD Application Team + * @brief Header file of I2C LL module. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef STM32F0xx_LL_I2C_H +#define STM32F0xx_LL_I2C_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f0xx.h" + +/** @addtogroup STM32F0xx_LL_Driver + * @{ + */ + +#if defined (I2C1) || defined (I2C2) + +/** @defgroup I2C_LL I2C + * @{ + */ + +/* Private types -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ + +/* Private constants ---------------------------------------------------------*/ +/** @defgroup I2C_LL_Private_Constants I2C Private Constants + * @{ + */ +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +#if defined(USE_FULL_LL_DRIVER) +/** @defgroup I2C_LL_Private_Macros I2C Private Macros + * @{ + */ +/** + * @} + */ +#endif /*USE_FULL_LL_DRIVER*/ + +/* Exported types ------------------------------------------------------------*/ +#if defined(USE_FULL_LL_DRIVER) +/** @defgroup I2C_LL_ES_INIT I2C Exported Init structure + * @{ + */ +typedef struct +{ + uint32_t PeripheralMode; /*!< Specifies the peripheral mode. + This parameter can be a value of @ref I2C_LL_EC_PERIPHERAL_MODE + + This feature can be modified afterwards using unitary function @ref LL_I2C_SetMode(). */ + + uint32_t Timing; /*!< Specifies the SDA setup, hold time and the SCL high, low period values. + This parameter must be set by referring to the STM32CubeMX Tool and + the helper macro @ref __LL_I2C_CONVERT_TIMINGS() + + This feature can be modified afterwards using unitary function @ref LL_I2C_SetTiming(). */ + + uint32_t AnalogFilter; /*!< Enables or disables analog noise filter. + This parameter can be a value of @ref I2C_LL_EC_ANALOGFILTER_SELECTION + + This feature can be modified afterwards using unitary functions @ref LL_I2C_EnableAnalogFilter() or LL_I2C_DisableAnalogFilter(). */ + + uint32_t DigitalFilter; /*!< Configures the digital noise filter. + This parameter can be a number between Min_Data = 0x00 and Max_Data = 0x0F + + This feature can be modified afterwards using unitary function @ref LL_I2C_SetDigitalFilter(). */ + + uint32_t OwnAddress1; /*!< Specifies the device own address 1. + This parameter must be a value between Min_Data = 0x00 and Max_Data = 0x3FF + + This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */ + + uint32_t TypeAcknowledge; /*!< Specifies the ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte. + This parameter can be a value of @ref I2C_LL_EC_I2C_ACKNOWLEDGE + + This feature can be modified afterwards using unitary function @ref LL_I2C_AcknowledgeNextData(). */ + + uint32_t OwnAddrSize; /*!< Specifies the device own address 1 size (7-bit or 10-bit). + This parameter can be a value of @ref I2C_LL_EC_OWNADDRESS1 + + This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */ +} LL_I2C_InitTypeDef; +/** + * @} + */ +#endif /*USE_FULL_LL_DRIVER*/ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup I2C_LL_Exported_Constants I2C Exported Constants + * @{ + */ + +/** @defgroup I2C_LL_EC_CLEAR_FLAG Clear Flags Defines + * @brief Flags defines which can be used with LL_I2C_WriteReg function + * @{ + */ +#define LL_I2C_ICR_ADDRCF I2C_ICR_ADDRCF /*!< Address Matched flag */ +#define LL_I2C_ICR_NACKCF I2C_ICR_NACKCF /*!< Not Acknowledge flag */ +#define LL_I2C_ICR_STOPCF I2C_ICR_STOPCF /*!< Stop detection flag */ +#define LL_I2C_ICR_BERRCF I2C_ICR_BERRCF /*!< Bus error flag */ +#define LL_I2C_ICR_ARLOCF I2C_ICR_ARLOCF /*!< Arbitration Lost flag */ +#define LL_I2C_ICR_OVRCF I2C_ICR_OVRCF /*!< Overrun/Underrun flag */ +#define LL_I2C_ICR_PECCF I2C_ICR_PECCF /*!< PEC error flag */ +#define LL_I2C_ICR_TIMOUTCF I2C_ICR_TIMOUTCF /*!< Timeout detection flag */ +#define LL_I2C_ICR_ALERTCF I2C_ICR_ALERTCF /*!< Alert flag */ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_GET_FLAG Get Flags Defines + * @brief Flags defines which can be used with LL_I2C_ReadReg function + * @{ + */ +#define LL_I2C_ISR_TXE I2C_ISR_TXE /*!< Transmit data register empty */ +#define LL_I2C_ISR_TXIS I2C_ISR_TXIS /*!< Transmit interrupt status */ +#define LL_I2C_ISR_RXNE I2C_ISR_RXNE /*!< Receive data register not empty */ +#define LL_I2C_ISR_ADDR I2C_ISR_ADDR /*!< Address matched (slave mode) */ +#define LL_I2C_ISR_NACKF I2C_ISR_NACKF /*!< Not Acknowledge received flag */ +#define LL_I2C_ISR_STOPF I2C_ISR_STOPF /*!< Stop detection flag */ +#define LL_I2C_ISR_TC I2C_ISR_TC /*!< Transfer Complete (master mode) */ +#define LL_I2C_ISR_TCR I2C_ISR_TCR /*!< Transfer Complete Reload */ +#define LL_I2C_ISR_BERR I2C_ISR_BERR /*!< Bus error */ +#define LL_I2C_ISR_ARLO I2C_ISR_ARLO /*!< Arbitration lost */ +#define LL_I2C_ISR_OVR I2C_ISR_OVR /*!< Overrun/Underrun (slave mode) */ +#define LL_I2C_ISR_PECERR I2C_ISR_PECERR /*!< PEC Error in reception (SMBus mode) */ +#define LL_I2C_ISR_TIMEOUT I2C_ISR_TIMEOUT /*!< Timeout detection flag (SMBus mode) */ +#define LL_I2C_ISR_ALERT I2C_ISR_ALERT /*!< SMBus alert (SMBus mode) */ +#define LL_I2C_ISR_BUSY I2C_ISR_BUSY /*!< Bus busy */ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_IT IT Defines + * @brief IT defines which can be used with LL_I2C_ReadReg and LL_I2C_WriteReg functions + * @{ + */ +#define LL_I2C_CR1_TXIE I2C_CR1_TXIE /*!< TX Interrupt enable */ +#define LL_I2C_CR1_RXIE I2C_CR1_RXIE /*!< RX Interrupt enable */ +#define LL_I2C_CR1_ADDRIE I2C_CR1_ADDRIE /*!< Address match Interrupt enable (slave only) */ +#define LL_I2C_CR1_NACKIE I2C_CR1_NACKIE /*!< Not acknowledge received Interrupt enable */ +#define LL_I2C_CR1_STOPIE I2C_CR1_STOPIE /*!< STOP detection Interrupt enable */ +#define LL_I2C_CR1_TCIE I2C_CR1_TCIE /*!< Transfer Complete interrupt enable */ +#define LL_I2C_CR1_ERRIE I2C_CR1_ERRIE /*!< Error interrupts enable */ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_PERIPHERAL_MODE Peripheral Mode + * @{ + */ +#define LL_I2C_MODE_I2C 0x00000000U /*!< I2C Master or Slave mode */ +#define LL_I2C_MODE_SMBUS_HOST I2C_CR1_SMBHEN /*!< SMBus Host address acknowledge */ +#define LL_I2C_MODE_SMBUS_DEVICE 0x00000000U /*!< SMBus Device default mode (Default address not acknowledge) */ +#define LL_I2C_MODE_SMBUS_DEVICE_ARP I2C_CR1_SMBDEN /*!< SMBus Device Default address acknowledge */ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_ANALOGFILTER_SELECTION Analog Filter Selection + * @{ + */ +#define LL_I2C_ANALOGFILTER_ENABLE 0x00000000U /*!< Analog filter is enabled. */ +#define LL_I2C_ANALOGFILTER_DISABLE I2C_CR1_ANFOFF /*!< Analog filter is disabled. */ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_ADDRESSING_MODE Master Addressing Mode + * @{ + */ +#define LL_I2C_ADDRESSING_MODE_7BIT 0x00000000U /*!< Master operates in 7-bit addressing mode. */ +#define LL_I2C_ADDRESSING_MODE_10BIT I2C_CR2_ADD10 /*!< Master operates in 10-bit addressing mode.*/ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_OWNADDRESS1 Own Address 1 Length + * @{ + */ +#define LL_I2C_OWNADDRESS1_7BIT 0x00000000U /*!< Own address 1 is a 7-bit address. */ +#define LL_I2C_OWNADDRESS1_10BIT I2C_OAR1_OA1MODE /*!< Own address 1 is a 10-bit address.*/ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_OWNADDRESS2 Own Address 2 Masks + * @{ + */ +#define LL_I2C_OWNADDRESS2_NOMASK I2C_OAR2_OA2NOMASK /*!< Own Address2 No mask. */ +#define LL_I2C_OWNADDRESS2_MASK01 I2C_OAR2_OA2MASK01 /*!< Only Address2 bits[7:2] are compared. */ +#define LL_I2C_OWNADDRESS2_MASK02 I2C_OAR2_OA2MASK02 /*!< Only Address2 bits[7:3] are compared. */ +#define LL_I2C_OWNADDRESS2_MASK03 I2C_OAR2_OA2MASK03 /*!< Only Address2 bits[7:4] are compared. */ +#define LL_I2C_OWNADDRESS2_MASK04 I2C_OAR2_OA2MASK04 /*!< Only Address2 bits[7:5] are compared. */ +#define LL_I2C_OWNADDRESS2_MASK05 I2C_OAR2_OA2MASK05 /*!< Only Address2 bits[7:6] are compared. */ +#define LL_I2C_OWNADDRESS2_MASK06 I2C_OAR2_OA2MASK06 /*!< Only Address2 bits[7] are compared. */ +#define LL_I2C_OWNADDRESS2_MASK07 I2C_OAR2_OA2MASK07 /*!< No comparison is done. All Address2 are acknowledged.*/ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_I2C_ACKNOWLEDGE Acknowledge Generation + * @{ + */ +#define LL_I2C_ACK 0x00000000U /*!< ACK is sent after current received byte. */ +#define LL_I2C_NACK I2C_CR2_NACK /*!< NACK is sent after current received byte.*/ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_ADDRSLAVE Slave Address Length + * @{ + */ +#define LL_I2C_ADDRSLAVE_7BIT 0x00000000U /*!< Slave Address in 7-bit. */ +#define LL_I2C_ADDRSLAVE_10BIT I2C_CR2_ADD10 /*!< Slave Address in 10-bit.*/ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_REQUEST Transfer Request Direction + * @{ + */ +#define LL_I2C_REQUEST_WRITE 0x00000000U /*!< Master request a write transfer. */ +#define LL_I2C_REQUEST_READ I2C_CR2_RD_WRN /*!< Master request a read transfer. */ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_MODE Transfer End Mode + * @{ + */ +#define LL_I2C_MODE_RELOAD I2C_CR2_RELOAD /*!< Enable I2C Reload mode. */ +#define LL_I2C_MODE_AUTOEND I2C_CR2_AUTOEND /*!< Enable I2C Automatic end mode with no HW PEC comparison. */ +#define LL_I2C_MODE_SOFTEND 0x00000000U /*!< Enable I2C Software end mode with no HW PEC comparison. */ +#define LL_I2C_MODE_SMBUS_RELOAD LL_I2C_MODE_RELOAD /*!< Enable SMBUS Automatic end mode with HW PEC comparison. */ +#define LL_I2C_MODE_SMBUS_AUTOEND_NO_PEC LL_I2C_MODE_AUTOEND /*!< Enable SMBUS Automatic end mode with HW PEC comparison. */ +#define LL_I2C_MODE_SMBUS_SOFTEND_NO_PEC LL_I2C_MODE_SOFTEND /*!< Enable SMBUS Software end mode with HW PEC comparison. */ +#define LL_I2C_MODE_SMBUS_AUTOEND_WITH_PEC (uint32_t)(LL_I2C_MODE_AUTOEND | I2C_CR2_PECBYTE) /*!< Enable SMBUS Automatic end mode with HW PEC comparison. */ +#define LL_I2C_MODE_SMBUS_SOFTEND_WITH_PEC (uint32_t)(LL_I2C_MODE_SOFTEND | I2C_CR2_PECBYTE) /*!< Enable SMBUS Software end mode with HW PEC comparison. */ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_GENERATE Start And Stop Generation + * @{ + */ +#define LL_I2C_GENERATE_NOSTARTSTOP 0x00000000U /*!< Don't Generate Stop and Start condition. */ +#define LL_I2C_GENERATE_STOP (uint32_t)(0x80000000U | I2C_CR2_STOP) /*!< Generate Stop condition (Size should be set to 0). */ +#define LL_I2C_GENERATE_START_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN) /*!< Generate Start for read request. */ +#define LL_I2C_GENERATE_START_WRITE (uint32_t)(0x80000000U | I2C_CR2_START) /*!< Generate Start for write request. */ +#define LL_I2C_GENERATE_RESTART_7BIT_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN) /*!< Generate Restart for read request, slave 7Bit address. */ +#define LL_I2C_GENERATE_RESTART_7BIT_WRITE (uint32_t)(0x80000000U | I2C_CR2_START) /*!< Generate Restart for write request, slave 7Bit address. */ +#define LL_I2C_GENERATE_RESTART_10BIT_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN | I2C_CR2_HEAD10R) /*!< Generate Restart for read request, slave 10Bit address. */ +#define LL_I2C_GENERATE_RESTART_10BIT_WRITE (uint32_t)(0x80000000U | I2C_CR2_START) /*!< Generate Restart for write request, slave 10Bit address.*/ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_DIRECTION Read Write Direction + * @{ + */ +#define LL_I2C_DIRECTION_WRITE 0x00000000U /*!< Write transfer request by master, slave enters receiver mode. */ +#define LL_I2C_DIRECTION_READ I2C_ISR_DIR /*!< Read transfer request by master, slave enters transmitter mode.*/ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_DMA_REG_DATA DMA Register Data + * @{ + */ +#define LL_I2C_DMA_REG_DATA_TRANSMIT 0x00000000U /*!< Get address of data register used for transmission */ +#define LL_I2C_DMA_REG_DATA_RECEIVE 0x00000001U /*!< Get address of data register used for reception */ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_SMBUS_TIMEOUTA_MODE SMBus TimeoutA Mode SCL SDA Timeout + * @{ + */ +#define LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW 0x00000000U /*!< TimeoutA is used to detect SCL low level timeout. */ +#define LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH I2C_TIMEOUTR_TIDLE /*!< TimeoutA is used to detect both SCL and SDA high level timeout.*/ +/** + * @} + */ + +/** @defgroup I2C_LL_EC_SMBUS_TIMEOUT_SELECTION SMBus Timeout Selection + * @{ + */ +#define LL_I2C_SMBUS_TIMEOUTA I2C_TIMEOUTR_TIMOUTEN /*!< TimeoutA enable bit */ +#define LL_I2C_SMBUS_TIMEOUTB I2C_TIMEOUTR_TEXTEN /*!< TimeoutB (extended clock) enable bit */ +#define LL_I2C_SMBUS_ALL_TIMEOUT (uint32_t)(I2C_TIMEOUTR_TIMOUTEN | I2C_TIMEOUTR_TEXTEN) /*!< TimeoutA and TimeoutB (extended clock) enable bits */ +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup I2C_LL_Exported_Macros I2C Exported Macros + * @{ + */ + +/** @defgroup I2C_LL_EM_WRITE_READ Common Write and read registers Macros + * @{ + */ + +/** + * @brief Write a value in I2C register + * @param __INSTANCE__ I2C Instance + * @param __REG__ Register to be written + * @param __VALUE__ Value to be written in the register + * @retval None + */ +#define LL_I2C_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG(__INSTANCE__->__REG__, (__VALUE__)) + +/** + * @brief Read a value in I2C register + * @param __INSTANCE__ I2C Instance + * @param __REG__ Register to be read + * @retval Register value + */ +#define LL_I2C_ReadReg(__INSTANCE__, __REG__) READ_REG(__INSTANCE__->__REG__) +/** + * @} + */ + +/** @defgroup I2C_LL_EM_CONVERT_TIMINGS Convert SDA SCL timings + * @{ + */ +/** + * @brief Configure the SDA setup, hold time and the SCL high, low period. + * @param __PRESCALER__ This parameter must be a value between Min_Data=0 and Max_Data=0xF. + * @param __DATA_SETUP_TIME__ This parameter must be a value between Min_Data=0 and Max_Data=0xF. (tscldel = (SCLDEL+1)xtpresc) + * @param __DATA_HOLD_TIME__ This parameter must be a value between Min_Data=0 and Max_Data=0xF. (tsdadel = SDADELxtpresc) + * @param __CLOCK_HIGH_PERIOD__ This parameter must be a value between Min_Data=0 and Max_Data=0xFF. (tsclh = (SCLH+1)xtpresc) + * @param __CLOCK_LOW_PERIOD__ This parameter must be a value between Min_Data=0 and Max_Data=0xFF. (tscll = (SCLL+1)xtpresc) + * @retval Value between Min_Data=0 and Max_Data=0xFFFFFFFF + */ +#define __LL_I2C_CONVERT_TIMINGS(__PRESCALER__, __DATA_SETUP_TIME__, __DATA_HOLD_TIME__, __CLOCK_HIGH_PERIOD__, __CLOCK_LOW_PERIOD__) \ + ((((uint32_t)(__PRESCALER__) << I2C_TIMINGR_PRESC_Pos) & I2C_TIMINGR_PRESC) | \ + (((uint32_t)(__DATA_SETUP_TIME__) << I2C_TIMINGR_SCLDEL_Pos) & I2C_TIMINGR_SCLDEL) | \ + (((uint32_t)(__DATA_HOLD_TIME__) << I2C_TIMINGR_SDADEL_Pos) & I2C_TIMINGR_SDADEL) | \ + (((uint32_t)(__CLOCK_HIGH_PERIOD__) << I2C_TIMINGR_SCLH_Pos) & I2C_TIMINGR_SCLH) | \ + (((uint32_t)(__CLOCK_LOW_PERIOD__) << I2C_TIMINGR_SCLL_Pos) & I2C_TIMINGR_SCLL)) +/** + * @} + */ + +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @defgroup I2C_LL_Exported_Functions I2C Exported Functions + * @{ + */ + +/** @defgroup I2C_LL_EF_Configuration Configuration + * @{ + */ + +/** + * @brief Enable I2C peripheral (PE = 1). + * @rmtoll CR1 PE LL_I2C_Enable + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_Enable(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_PE); +} + +/** + * @brief Disable I2C peripheral (PE = 0). + * @note When PE = 0, the I2C SCL and SDA lines are released. + * Internal state machines and status bits are put back to their reset value. + * When cleared, PE must be kept low for at least 3 APB clock cycles. + * @rmtoll CR1 PE LL_I2C_Disable + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_Disable(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_PE); +} + +/** + * @brief Check if the I2C peripheral is enabled or disabled. + * @rmtoll CR1 PE LL_I2C_IsEnabled + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabled(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_PE) == (I2C_CR1_PE)) ? 1UL : 0UL); +} + +/** + * @brief Configure Noise Filters (Analog and Digital). + * @note If the analog filter is also enabled, the digital filter is added to analog filter. + * The filters can only be programmed when the I2C is disabled (PE = 0). + * @rmtoll CR1 ANFOFF LL_I2C_ConfigFilters\n + * CR1 DNF LL_I2C_ConfigFilters + * @param I2Cx I2C Instance. + * @param AnalogFilter This parameter can be one of the following values: + * @arg @ref LL_I2C_ANALOGFILTER_ENABLE + * @arg @ref LL_I2C_ANALOGFILTER_DISABLE + * @param DigitalFilter This parameter must be a value between Min_Data=0x00 (Digital filter disabled) and Max_Data=0x0F (Digital filter enabled and filtering capability up to 15*ti2cclk). + * This parameter is used to configure the digital noise filter on SDA and SCL input. + * The digital filter will filter spikes with a length of up to DNF[3:0]*ti2cclk. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ConfigFilters(I2C_TypeDef *I2Cx, uint32_t AnalogFilter, uint32_t DigitalFilter) +{ + MODIFY_REG(I2Cx->CR1, I2C_CR1_ANFOFF | I2C_CR1_DNF, AnalogFilter | (DigitalFilter << I2C_CR1_DNF_Pos)); +} + +/** + * @brief Configure Digital Noise Filter. + * @note If the analog filter is also enabled, the digital filter is added to analog filter. + * This filter can only be programmed when the I2C is disabled (PE = 0). + * @rmtoll CR1 DNF LL_I2C_SetDigitalFilter + * @param I2Cx I2C Instance. + * @param DigitalFilter This parameter must be a value between Min_Data=0x00 (Digital filter disabled) and Max_Data=0x0F (Digital filter enabled and filtering capability up to 15*ti2cclk). + * This parameter is used to configure the digital noise filter on SDA and SCL input. + * The digital filter will filter spikes with a length of up to DNF[3:0]*ti2cclk. + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetDigitalFilter(I2C_TypeDef *I2Cx, uint32_t DigitalFilter) +{ + MODIFY_REG(I2Cx->CR1, I2C_CR1_DNF, DigitalFilter << I2C_CR1_DNF_Pos); +} + +/** + * @brief Get the current Digital Noise Filter configuration. + * @rmtoll CR1 DNF LL_I2C_GetDigitalFilter + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x0 and Max_Data=0xF + */ +__STATIC_INLINE uint32_t LL_I2C_GetDigitalFilter(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->CR1, I2C_CR1_DNF) >> I2C_CR1_DNF_Pos); +} + +/** + * @brief Enable Analog Noise Filter. + * @note This filter can only be programmed when the I2C is disabled (PE = 0). + * @rmtoll CR1 ANFOFF LL_I2C_EnableAnalogFilter + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableAnalogFilter(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_ANFOFF); +} + +/** + * @brief Disable Analog Noise Filter. + * @note This filter can only be programmed when the I2C is disabled (PE = 0). + * @rmtoll CR1 ANFOFF LL_I2C_DisableAnalogFilter + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableAnalogFilter(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_ANFOFF); +} + +/** + * @brief Check if Analog Noise Filter is enabled or disabled. + * @rmtoll CR1 ANFOFF LL_I2C_IsEnabledAnalogFilter + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledAnalogFilter(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_ANFOFF) != (I2C_CR1_ANFOFF)) ? 1UL : 0UL); +} + +/** + * @brief Enable DMA transmission requests. + * @rmtoll CR1 TXDMAEN LL_I2C_EnableDMAReq_TX + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableDMAReq_TX(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_TXDMAEN); +} + +/** + * @brief Disable DMA transmission requests. + * @rmtoll CR1 TXDMAEN LL_I2C_DisableDMAReq_TX + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableDMAReq_TX(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_TXDMAEN); +} + +/** + * @brief Check if DMA transmission requests are enabled or disabled. + * @rmtoll CR1 TXDMAEN LL_I2C_IsEnabledDMAReq_TX + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_TX(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_TXDMAEN) == (I2C_CR1_TXDMAEN)) ? 1UL : 0UL); +} + +/** + * @brief Enable DMA reception requests. + * @rmtoll CR1 RXDMAEN LL_I2C_EnableDMAReq_RX + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableDMAReq_RX(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_RXDMAEN); +} + +/** + * @brief Disable DMA reception requests. + * @rmtoll CR1 RXDMAEN LL_I2C_DisableDMAReq_RX + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableDMAReq_RX(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_RXDMAEN); +} + +/** + * @brief Check if DMA reception requests are enabled or disabled. + * @rmtoll CR1 RXDMAEN LL_I2C_IsEnabledDMAReq_RX + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_RX(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_RXDMAEN) == (I2C_CR1_RXDMAEN)) ? 1UL : 0UL); +} + +/** + * @brief Get the data register address used for DMA transfer + * @rmtoll TXDR TXDATA LL_I2C_DMA_GetRegAddr\n + * RXDR RXDATA LL_I2C_DMA_GetRegAddr + * @param I2Cx I2C Instance + * @param Direction This parameter can be one of the following values: + * @arg @ref LL_I2C_DMA_REG_DATA_TRANSMIT + * @arg @ref LL_I2C_DMA_REG_DATA_RECEIVE + * @retval Address of data register + */ +__STATIC_INLINE uint32_t LL_I2C_DMA_GetRegAddr(I2C_TypeDef *I2Cx, uint32_t Direction) +{ + register uint32_t data_reg_addr; + + if (Direction == LL_I2C_DMA_REG_DATA_TRANSMIT) + { + /* return address of TXDR register */ + data_reg_addr = (uint32_t) & (I2Cx->TXDR); + } + else + { + /* return address of RXDR register */ + data_reg_addr = (uint32_t) & (I2Cx->RXDR); + } + + return data_reg_addr; +} + +/** + * @brief Enable Clock stretching. + * @note This bit can only be programmed when the I2C is disabled (PE = 0). + * @rmtoll CR1 NOSTRETCH LL_I2C_EnableClockStretching + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableClockStretching(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH); +} + +/** + * @brief Disable Clock stretching. + * @note This bit can only be programmed when the I2C is disabled (PE = 0). + * @rmtoll CR1 NOSTRETCH LL_I2C_DisableClockStretching + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableClockStretching(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH); +} + +/** + * @brief Check if Clock stretching is enabled or disabled. + * @rmtoll CR1 NOSTRETCH LL_I2C_IsEnabledClockStretching + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledClockStretching(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH) != (I2C_CR1_NOSTRETCH)) ? 1UL : 0UL); +} + +/** + * @brief Enable hardware byte control in slave mode. + * @rmtoll CR1 SBC LL_I2C_EnableSlaveByteControl + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableSlaveByteControl(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_SBC); +} + +/** + * @brief Disable hardware byte control in slave mode. + * @rmtoll CR1 SBC LL_I2C_DisableSlaveByteControl + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableSlaveByteControl(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_SBC); +} + +/** + * @brief Check if hardware byte control in slave mode is enabled or disabled. + * @rmtoll CR1 SBC LL_I2C_IsEnabledSlaveByteControl + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledSlaveByteControl(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_SBC) == (I2C_CR1_SBC)) ? 1UL : 0UL); +} + +#if defined(I2C_CR1_WUPEN) +/** + * @brief Enable Wakeup from STOP. + * @note Macro @ref IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not + * WakeUpFromStop feature is supported by the I2Cx Instance. + * @note This bit can only be programmed when Digital Filter is disabled. + * @rmtoll CR1 WUPEN LL_I2C_EnableWakeUpFromStop + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableWakeUpFromStop(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_WUPEN); +} + +/** + * @brief Disable Wakeup from STOP. + * @note Macro @ref IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not + * WakeUpFromStop feature is supported by the I2Cx Instance. + * @rmtoll CR1 WUPEN LL_I2C_DisableWakeUpFromStop + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableWakeUpFromStop(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_WUPEN); +} + +/** + * @brief Check if Wakeup from STOP is enabled or disabled. + * @note Macro @ref IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not + * WakeUpFromStop feature is supported by the I2Cx Instance. + * @rmtoll CR1 WUPEN LL_I2C_IsEnabledWakeUpFromStop + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledWakeUpFromStop(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_WUPEN) == (I2C_CR1_WUPEN)) ? 1UL : 0UL); +} +#endif + +/** + * @brief Enable General Call. + * @note When enabled the Address 0x00 is ACKed. + * @rmtoll CR1 GCEN LL_I2C_EnableGeneralCall + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableGeneralCall(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_GCEN); +} + +/** + * @brief Disable General Call. + * @note When disabled the Address 0x00 is NACKed. + * @rmtoll CR1 GCEN LL_I2C_DisableGeneralCall + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableGeneralCall(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_GCEN); +} + +/** + * @brief Check if General Call is enabled or disabled. + * @rmtoll CR1 GCEN LL_I2C_IsEnabledGeneralCall + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledGeneralCall(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_GCEN) == (I2C_CR1_GCEN)) ? 1UL : 0UL); +} + +/** + * @brief Configure the Master to operate in 7-bit or 10-bit addressing mode. + * @note Changing this bit is not allowed, when the START bit is set. + * @rmtoll CR2 ADD10 LL_I2C_SetMasterAddressingMode + * @param I2Cx I2C Instance. + * @param AddressingMode This parameter can be one of the following values: + * @arg @ref LL_I2C_ADDRESSING_MODE_7BIT + * @arg @ref LL_I2C_ADDRESSING_MODE_10BIT + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetMasterAddressingMode(I2C_TypeDef *I2Cx, uint32_t AddressingMode) +{ + MODIFY_REG(I2Cx->CR2, I2C_CR2_ADD10, AddressingMode); +} + +/** + * @brief Get the Master addressing mode. + * @rmtoll CR2 ADD10 LL_I2C_GetMasterAddressingMode + * @param I2Cx I2C Instance. + * @retval Returned value can be one of the following values: + * @arg @ref LL_I2C_ADDRESSING_MODE_7BIT + * @arg @ref LL_I2C_ADDRESSING_MODE_10BIT + */ +__STATIC_INLINE uint32_t LL_I2C_GetMasterAddressingMode(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->CR2, I2C_CR2_ADD10)); +} + +/** + * @brief Set the Own Address1. + * @rmtoll OAR1 OA1 LL_I2C_SetOwnAddress1\n + * OAR1 OA1MODE LL_I2C_SetOwnAddress1 + * @param I2Cx I2C Instance. + * @param OwnAddress1 This parameter must be a value between Min_Data=0 and Max_Data=0x3FF. + * @param OwnAddrSize This parameter can be one of the following values: + * @arg @ref LL_I2C_OWNADDRESS1_7BIT + * @arg @ref LL_I2C_OWNADDRESS1_10BIT + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetOwnAddress1(I2C_TypeDef *I2Cx, uint32_t OwnAddress1, uint32_t OwnAddrSize) +{ + MODIFY_REG(I2Cx->OAR1, I2C_OAR1_OA1 | I2C_OAR1_OA1MODE, OwnAddress1 | OwnAddrSize); +} + +/** + * @brief Enable acknowledge on Own Address1 match address. + * @rmtoll OAR1 OA1EN LL_I2C_EnableOwnAddress1 + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableOwnAddress1(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->OAR1, I2C_OAR1_OA1EN); +} + +/** + * @brief Disable acknowledge on Own Address1 match address. + * @rmtoll OAR1 OA1EN LL_I2C_DisableOwnAddress1 + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableOwnAddress1(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->OAR1, I2C_OAR1_OA1EN); +} + +/** + * @brief Check if Own Address1 acknowledge is enabled or disabled. + * @rmtoll OAR1 OA1EN LL_I2C_IsEnabledOwnAddress1 + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledOwnAddress1(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->OAR1, I2C_OAR1_OA1EN) == (I2C_OAR1_OA1EN)) ? 1UL : 0UL); +} + +/** + * @brief Set the 7bits Own Address2. + * @note This action has no effect if own address2 is enabled. + * @rmtoll OAR2 OA2 LL_I2C_SetOwnAddress2\n + * OAR2 OA2MSK LL_I2C_SetOwnAddress2 + * @param I2Cx I2C Instance. + * @param OwnAddress2 Value between Min_Data=0 and Max_Data=0x7F. + * @param OwnAddrMask This parameter can be one of the following values: + * @arg @ref LL_I2C_OWNADDRESS2_NOMASK + * @arg @ref LL_I2C_OWNADDRESS2_MASK01 + * @arg @ref LL_I2C_OWNADDRESS2_MASK02 + * @arg @ref LL_I2C_OWNADDRESS2_MASK03 + * @arg @ref LL_I2C_OWNADDRESS2_MASK04 + * @arg @ref LL_I2C_OWNADDRESS2_MASK05 + * @arg @ref LL_I2C_OWNADDRESS2_MASK06 + * @arg @ref LL_I2C_OWNADDRESS2_MASK07 + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetOwnAddress2(I2C_TypeDef *I2Cx, uint32_t OwnAddress2, uint32_t OwnAddrMask) +{ + MODIFY_REG(I2Cx->OAR2, I2C_OAR2_OA2 | I2C_OAR2_OA2MSK, OwnAddress2 | OwnAddrMask); +} + +/** + * @brief Enable acknowledge on Own Address2 match address. + * @rmtoll OAR2 OA2EN LL_I2C_EnableOwnAddress2 + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableOwnAddress2(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->OAR2, I2C_OAR2_OA2EN); +} + +/** + * @brief Disable acknowledge on Own Address2 match address. + * @rmtoll OAR2 OA2EN LL_I2C_DisableOwnAddress2 + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableOwnAddress2(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->OAR2, I2C_OAR2_OA2EN); +} + +/** + * @brief Check if Own Address1 acknowledge is enabled or disabled. + * @rmtoll OAR2 OA2EN LL_I2C_IsEnabledOwnAddress2 + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledOwnAddress2(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->OAR2, I2C_OAR2_OA2EN) == (I2C_OAR2_OA2EN)) ? 1UL : 0UL); +} + +/** + * @brief Configure the SDA setup, hold time and the SCL high, low period. + * @note This bit can only be programmed when the I2C is disabled (PE = 0). + * @rmtoll TIMINGR TIMINGR LL_I2C_SetTiming + * @param I2Cx I2C Instance. + * @param Timing This parameter must be a value between Min_Data=0 and Max_Data=0xFFFFFFFF. + * @note This parameter is computed with the STM32CubeMX Tool. + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetTiming(I2C_TypeDef *I2Cx, uint32_t Timing) +{ + WRITE_REG(I2Cx->TIMINGR, Timing); +} + +/** + * @brief Get the Timing Prescaler setting. + * @rmtoll TIMINGR PRESC LL_I2C_GetTimingPrescaler + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x0 and Max_Data=0xF + */ +__STATIC_INLINE uint32_t LL_I2C_GetTimingPrescaler(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_PRESC) >> I2C_TIMINGR_PRESC_Pos); +} + +/** + * @brief Get the SCL low period setting. + * @rmtoll TIMINGR SCLL LL_I2C_GetClockLowPeriod + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x00 and Max_Data=0xFF + */ +__STATIC_INLINE uint32_t LL_I2C_GetClockLowPeriod(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_SCLL) >> I2C_TIMINGR_SCLL_Pos); +} + +/** + * @brief Get the SCL high period setting. + * @rmtoll TIMINGR SCLH LL_I2C_GetClockHighPeriod + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x00 and Max_Data=0xFF + */ +__STATIC_INLINE uint32_t LL_I2C_GetClockHighPeriod(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_SCLH) >> I2C_TIMINGR_SCLH_Pos); +} + +/** + * @brief Get the SDA hold time. + * @rmtoll TIMINGR SDADEL LL_I2C_GetDataHoldTime + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x0 and Max_Data=0xF + */ +__STATIC_INLINE uint32_t LL_I2C_GetDataHoldTime(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_SDADEL) >> I2C_TIMINGR_SDADEL_Pos); +} + +/** + * @brief Get the SDA setup time. + * @rmtoll TIMINGR SCLDEL LL_I2C_GetDataSetupTime + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x0 and Max_Data=0xF + */ +__STATIC_INLINE uint32_t LL_I2C_GetDataSetupTime(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_SCLDEL) >> I2C_TIMINGR_SCLDEL_Pos); +} + +/** + * @brief Configure peripheral mode. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll CR1 SMBHEN LL_I2C_SetMode\n + * CR1 SMBDEN LL_I2C_SetMode + * @param I2Cx I2C Instance. + * @param PeripheralMode This parameter can be one of the following values: + * @arg @ref LL_I2C_MODE_I2C + * @arg @ref LL_I2C_MODE_SMBUS_HOST + * @arg @ref LL_I2C_MODE_SMBUS_DEVICE + * @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetMode(I2C_TypeDef *I2Cx, uint32_t PeripheralMode) +{ + MODIFY_REG(I2Cx->CR1, I2C_CR1_SMBHEN | I2C_CR1_SMBDEN, PeripheralMode); +} + +/** + * @brief Get peripheral mode. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll CR1 SMBHEN LL_I2C_GetMode\n + * CR1 SMBDEN LL_I2C_GetMode + * @param I2Cx I2C Instance. + * @retval Returned value can be one of the following values: + * @arg @ref LL_I2C_MODE_I2C + * @arg @ref LL_I2C_MODE_SMBUS_HOST + * @arg @ref LL_I2C_MODE_SMBUS_DEVICE + * @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP + */ +__STATIC_INLINE uint32_t LL_I2C_GetMode(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->CR1, I2C_CR1_SMBHEN | I2C_CR1_SMBDEN)); +} + +/** + * @brief Enable SMBus alert (Host or Device mode) + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note SMBus Device mode: + * - SMBus Alert pin is drived low and + * Alert Response Address Header acknowledge is enabled. + * SMBus Host mode: + * - SMBus Alert pin management is supported. + * @rmtoll CR1 ALERTEN LL_I2C_EnableSMBusAlert + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableSMBusAlert(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_ALERTEN); +} + +/** + * @brief Disable SMBus alert (Host or Device mode) + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note SMBus Device mode: + * - SMBus Alert pin is not drived (can be used as a standard GPIO) and + * Alert Response Address Header acknowledge is disabled. + * SMBus Host mode: + * - SMBus Alert pin management is not supported. + * @rmtoll CR1 ALERTEN LL_I2C_DisableSMBusAlert + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableSMBusAlert(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_ALERTEN); +} + +/** + * @brief Check if SMBus alert (Host or Device mode) is enabled or disabled. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll CR1 ALERTEN LL_I2C_IsEnabledSMBusAlert + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusAlert(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_ALERTEN) == (I2C_CR1_ALERTEN)) ? 1UL : 0UL); +} + +/** + * @brief Enable SMBus Packet Error Calculation (PEC). + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll CR1 PECEN LL_I2C_EnableSMBusPEC + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableSMBusPEC(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_PECEN); +} + +/** + * @brief Disable SMBus Packet Error Calculation (PEC). + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll CR1 PECEN LL_I2C_DisableSMBusPEC + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableSMBusPEC(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_PECEN); +} + +/** + * @brief Check if SMBus Packet Error Calculation (PEC) is enabled or disabled. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll CR1 PECEN LL_I2C_IsEnabledSMBusPEC + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPEC(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_PECEN) == (I2C_CR1_PECEN)) ? 1UL : 0UL); +} + +/** + * @brief Configure the SMBus Clock Timeout. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note This configuration can only be programmed when associated Timeout is disabled (TimeoutA and/orTimeoutB). + * @rmtoll TIMEOUTR TIMEOUTA LL_I2C_ConfigSMBusTimeout\n + * TIMEOUTR TIDLE LL_I2C_ConfigSMBusTimeout\n + * TIMEOUTR TIMEOUTB LL_I2C_ConfigSMBusTimeout + * @param I2Cx I2C Instance. + * @param TimeoutA This parameter must be a value between Min_Data=0 and Max_Data=0xFFF. + * @param TimeoutAMode This parameter can be one of the following values: + * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW + * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH + * @param TimeoutB + * @retval None + */ +__STATIC_INLINE void LL_I2C_ConfigSMBusTimeout(I2C_TypeDef *I2Cx, uint32_t TimeoutA, uint32_t TimeoutAMode, + uint32_t TimeoutB) +{ + MODIFY_REG(I2Cx->TIMEOUTR, I2C_TIMEOUTR_TIMEOUTA | I2C_TIMEOUTR_TIDLE | I2C_TIMEOUTR_TIMEOUTB, + TimeoutA | TimeoutAMode | (TimeoutB << I2C_TIMEOUTR_TIMEOUTB_Pos)); +} + +/** + * @brief Configure the SMBus Clock TimeoutA (SCL low timeout or SCL and SDA high timeout depends on TimeoutA mode). + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note These bits can only be programmed when TimeoutA is disabled. + * @rmtoll TIMEOUTR TIMEOUTA LL_I2C_SetSMBusTimeoutA + * @param I2Cx I2C Instance. + * @param TimeoutA This parameter must be a value between Min_Data=0 and Max_Data=0xFFF. + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetSMBusTimeoutA(I2C_TypeDef *I2Cx, uint32_t TimeoutA) +{ + WRITE_REG(I2Cx->TIMEOUTR, TimeoutA); +} + +/** + * @brief Get the SMBus Clock TimeoutA setting. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll TIMEOUTR TIMEOUTA LL_I2C_GetSMBusTimeoutA + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0 and Max_Data=0xFFF + */ +__STATIC_INLINE uint32_t LL_I2C_GetSMBusTimeoutA(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->TIMEOUTR, I2C_TIMEOUTR_TIMEOUTA)); +} + +/** + * @brief Set the SMBus Clock TimeoutA mode. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note This bit can only be programmed when TimeoutA is disabled. + * @rmtoll TIMEOUTR TIDLE LL_I2C_SetSMBusTimeoutAMode + * @param I2Cx I2C Instance. + * @param TimeoutAMode This parameter can be one of the following values: + * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW + * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetSMBusTimeoutAMode(I2C_TypeDef *I2Cx, uint32_t TimeoutAMode) +{ + WRITE_REG(I2Cx->TIMEOUTR, TimeoutAMode); +} + +/** + * @brief Get the SMBus Clock TimeoutA mode. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll TIMEOUTR TIDLE LL_I2C_GetSMBusTimeoutAMode + * @param I2Cx I2C Instance. + * @retval Returned value can be one of the following values: + * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW + * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH + */ +__STATIC_INLINE uint32_t LL_I2C_GetSMBusTimeoutAMode(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->TIMEOUTR, I2C_TIMEOUTR_TIDLE)); +} + +/** + * @brief Configure the SMBus Extended Cumulative Clock TimeoutB (Master or Slave mode). + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note These bits can only be programmed when TimeoutB is disabled. + * @rmtoll TIMEOUTR TIMEOUTB LL_I2C_SetSMBusTimeoutB + * @param I2Cx I2C Instance. + * @param TimeoutB This parameter must be a value between Min_Data=0 and Max_Data=0xFFF. + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetSMBusTimeoutB(I2C_TypeDef *I2Cx, uint32_t TimeoutB) +{ + WRITE_REG(I2Cx->TIMEOUTR, TimeoutB << I2C_TIMEOUTR_TIMEOUTB_Pos); +} + +/** + * @brief Get the SMBus Extented Cumulative Clock TimeoutB setting. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll TIMEOUTR TIMEOUTB LL_I2C_GetSMBusTimeoutB + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0 and Max_Data=0xFFF + */ +__STATIC_INLINE uint32_t LL_I2C_GetSMBusTimeoutB(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->TIMEOUTR, I2C_TIMEOUTR_TIMEOUTB) >> I2C_TIMEOUTR_TIMEOUTB_Pos); +} + +/** + * @brief Enable the SMBus Clock Timeout. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll TIMEOUTR TIMOUTEN LL_I2C_EnableSMBusTimeout\n + * TIMEOUTR TEXTEN LL_I2C_EnableSMBusTimeout + * @param I2Cx I2C Instance. + * @param ClockTimeout This parameter can be one of the following values: + * @arg @ref LL_I2C_SMBUS_TIMEOUTA + * @arg @ref LL_I2C_SMBUS_TIMEOUTB + * @arg @ref LL_I2C_SMBUS_ALL_TIMEOUT + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableSMBusTimeout(I2C_TypeDef *I2Cx, uint32_t ClockTimeout) +{ + SET_BIT(I2Cx->TIMEOUTR, ClockTimeout); +} + +/** + * @brief Disable the SMBus Clock Timeout. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll TIMEOUTR TIMOUTEN LL_I2C_DisableSMBusTimeout\n + * TIMEOUTR TEXTEN LL_I2C_DisableSMBusTimeout + * @param I2Cx I2C Instance. + * @param ClockTimeout This parameter can be one of the following values: + * @arg @ref LL_I2C_SMBUS_TIMEOUTA + * @arg @ref LL_I2C_SMBUS_TIMEOUTB + * @arg @ref LL_I2C_SMBUS_ALL_TIMEOUT + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableSMBusTimeout(I2C_TypeDef *I2Cx, uint32_t ClockTimeout) +{ + CLEAR_BIT(I2Cx->TIMEOUTR, ClockTimeout); +} + +/** + * @brief Check if the SMBus Clock Timeout is enabled or disabled. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll TIMEOUTR TIMOUTEN LL_I2C_IsEnabledSMBusTimeout\n + * TIMEOUTR TEXTEN LL_I2C_IsEnabledSMBusTimeout + * @param I2Cx I2C Instance. + * @param ClockTimeout This parameter can be one of the following values: + * @arg @ref LL_I2C_SMBUS_TIMEOUTA + * @arg @ref LL_I2C_SMBUS_TIMEOUTB + * @arg @ref LL_I2C_SMBUS_ALL_TIMEOUT + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusTimeout(I2C_TypeDef *I2Cx, uint32_t ClockTimeout) +{ + return ((READ_BIT(I2Cx->TIMEOUTR, (I2C_TIMEOUTR_TIMOUTEN | I2C_TIMEOUTR_TEXTEN)) == (ClockTimeout)) ? 1UL : 0UL); +} + +/** + * @} + */ + +/** @defgroup I2C_LL_EF_IT_Management IT_Management + * @{ + */ + +/** + * @brief Enable TXIS interrupt. + * @rmtoll CR1 TXIE LL_I2C_EnableIT_TX + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableIT_TX(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_TXIE); +} + +/** + * @brief Disable TXIS interrupt. + * @rmtoll CR1 TXIE LL_I2C_DisableIT_TX + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableIT_TX(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_TXIE); +} + +/** + * @brief Check if the TXIS Interrupt is enabled or disabled. + * @rmtoll CR1 TXIE LL_I2C_IsEnabledIT_TX + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_TX(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_TXIE) == (I2C_CR1_TXIE)) ? 1UL : 0UL); +} + +/** + * @brief Enable RXNE interrupt. + * @rmtoll CR1 RXIE LL_I2C_EnableIT_RX + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableIT_RX(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_RXIE); +} + +/** + * @brief Disable RXNE interrupt. + * @rmtoll CR1 RXIE LL_I2C_DisableIT_RX + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableIT_RX(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_RXIE); +} + +/** + * @brief Check if the RXNE Interrupt is enabled or disabled. + * @rmtoll CR1 RXIE LL_I2C_IsEnabledIT_RX + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_RX(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_RXIE) == (I2C_CR1_RXIE)) ? 1UL : 0UL); +} + +/** + * @brief Enable Address match interrupt (slave mode only). + * @rmtoll CR1 ADDRIE LL_I2C_EnableIT_ADDR + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableIT_ADDR(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_ADDRIE); +} + +/** + * @brief Disable Address match interrupt (slave mode only). + * @rmtoll CR1 ADDRIE LL_I2C_DisableIT_ADDR + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableIT_ADDR(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_ADDRIE); +} + +/** + * @brief Check if Address match interrupt is enabled or disabled. + * @rmtoll CR1 ADDRIE LL_I2C_IsEnabledIT_ADDR + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_ADDR(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_ADDRIE) == (I2C_CR1_ADDRIE)) ? 1UL : 0UL); +} + +/** + * @brief Enable Not acknowledge received interrupt. + * @rmtoll CR1 NACKIE LL_I2C_EnableIT_NACK + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableIT_NACK(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_NACKIE); +} + +/** + * @brief Disable Not acknowledge received interrupt. + * @rmtoll CR1 NACKIE LL_I2C_DisableIT_NACK + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableIT_NACK(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_NACKIE); +} + +/** + * @brief Check if Not acknowledge received interrupt is enabled or disabled. + * @rmtoll CR1 NACKIE LL_I2C_IsEnabledIT_NACK + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_NACK(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_NACKIE) == (I2C_CR1_NACKIE)) ? 1UL : 0UL); +} + +/** + * @brief Enable STOP detection interrupt. + * @rmtoll CR1 STOPIE LL_I2C_EnableIT_STOP + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableIT_STOP(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_STOPIE); +} + +/** + * @brief Disable STOP detection interrupt. + * @rmtoll CR1 STOPIE LL_I2C_DisableIT_STOP + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableIT_STOP(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_STOPIE); +} + +/** + * @brief Check if STOP detection interrupt is enabled or disabled. + * @rmtoll CR1 STOPIE LL_I2C_IsEnabledIT_STOP + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_STOP(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_STOPIE) == (I2C_CR1_STOPIE)) ? 1UL : 0UL); +} + +/** + * @brief Enable Transfer Complete interrupt. + * @note Any of these events will generate interrupt : + * Transfer Complete (TC) + * Transfer Complete Reload (TCR) + * @rmtoll CR1 TCIE LL_I2C_EnableIT_TC + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableIT_TC(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_TCIE); +} + +/** + * @brief Disable Transfer Complete interrupt. + * @note Any of these events will generate interrupt : + * Transfer Complete (TC) + * Transfer Complete Reload (TCR) + * @rmtoll CR1 TCIE LL_I2C_DisableIT_TC + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableIT_TC(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_TCIE); +} + +/** + * @brief Check if Transfer Complete interrupt is enabled or disabled. + * @rmtoll CR1 TCIE LL_I2C_IsEnabledIT_TC + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_TC(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_TCIE) == (I2C_CR1_TCIE)) ? 1UL : 0UL); +} + +/** + * @brief Enable Error interrupts. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note Any of these errors will generate interrupt : + * Arbitration Loss (ARLO) + * Bus Error detection (BERR) + * Overrun/Underrun (OVR) + * SMBus Timeout detection (TIMEOUT) + * SMBus PEC error detection (PECERR) + * SMBus Alert pin event detection (ALERT) + * @rmtoll CR1 ERRIE LL_I2C_EnableIT_ERR + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableIT_ERR(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR1, I2C_CR1_ERRIE); +} + +/** + * @brief Disable Error interrupts. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note Any of these errors will generate interrupt : + * Arbitration Loss (ARLO) + * Bus Error detection (BERR) + * Overrun/Underrun (OVR) + * SMBus Timeout detection (TIMEOUT) + * SMBus PEC error detection (PECERR) + * SMBus Alert pin event detection (ALERT) + * @rmtoll CR1 ERRIE LL_I2C_DisableIT_ERR + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableIT_ERR(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR1, I2C_CR1_ERRIE); +} + +/** + * @brief Check if Error interrupts are enabled or disabled. + * @rmtoll CR1 ERRIE LL_I2C_IsEnabledIT_ERR + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_ERR(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR1, I2C_CR1_ERRIE) == (I2C_CR1_ERRIE)) ? 1UL : 0UL); +} + +/** + * @} + */ + +/** @defgroup I2C_LL_EF_FLAG_management FLAG_management + * @{ + */ + +/** + * @brief Indicate the status of Transmit data register empty flag. + * @note RESET: When next data is written in Transmit data register. + * SET: When Transmit data register is empty. + * @rmtoll ISR TXE LL_I2C_IsActiveFlag_TXE + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TXE(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_TXE) == (I2C_ISR_TXE)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Transmit interrupt flag. + * @note RESET: When next data is written in Transmit data register. + * SET: When Transmit data register is empty. + * @rmtoll ISR TXIS LL_I2C_IsActiveFlag_TXIS + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TXIS(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_TXIS) == (I2C_ISR_TXIS)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Receive data register not empty flag. + * @note RESET: When Receive data register is read. + * SET: When the received data is copied in Receive data register. + * @rmtoll ISR RXNE LL_I2C_IsActiveFlag_RXNE + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_RXNE(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_RXNE) == (I2C_ISR_RXNE)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Address matched flag (slave mode). + * @note RESET: Clear default value. + * SET: When the received slave address matched with one of the enabled slave address. + * @rmtoll ISR ADDR LL_I2C_IsActiveFlag_ADDR + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ADDR(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_ADDR) == (I2C_ISR_ADDR)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Not Acknowledge received flag. + * @note RESET: Clear default value. + * SET: When a NACK is received after a byte transmission. + * @rmtoll ISR NACKF LL_I2C_IsActiveFlag_NACK + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_NACK(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_NACKF) == (I2C_ISR_NACKF)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Stop detection flag. + * @note RESET: Clear default value. + * SET: When a Stop condition is detected. + * @rmtoll ISR STOPF LL_I2C_IsActiveFlag_STOP + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_STOP(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_STOPF) == (I2C_ISR_STOPF)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Transfer complete flag (master mode). + * @note RESET: Clear default value. + * SET: When RELOAD=0, AUTOEND=0 and NBYTES date have been transferred. + * @rmtoll ISR TC LL_I2C_IsActiveFlag_TC + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TC(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_TC) == (I2C_ISR_TC)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Transfer complete flag (master mode). + * @note RESET: Clear default value. + * SET: When RELOAD=1 and NBYTES date have been transferred. + * @rmtoll ISR TCR LL_I2C_IsActiveFlag_TCR + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TCR(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_TCR) == (I2C_ISR_TCR)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Bus error flag. + * @note RESET: Clear default value. + * SET: When a misplaced Start or Stop condition is detected. + * @rmtoll ISR BERR LL_I2C_IsActiveFlag_BERR + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BERR(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_BERR) == (I2C_ISR_BERR)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Arbitration lost flag. + * @note RESET: Clear default value. + * SET: When arbitration lost. + * @rmtoll ISR ARLO LL_I2C_IsActiveFlag_ARLO + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ARLO(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_ARLO) == (I2C_ISR_ARLO)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Overrun/Underrun flag (slave mode). + * @note RESET: Clear default value. + * SET: When an overrun/underrun error occurs (Clock Stretching Disabled). + * @rmtoll ISR OVR LL_I2C_IsActiveFlag_OVR + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_OVR(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_OVR) == (I2C_ISR_OVR)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of SMBus PEC error flag in reception. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note RESET: Clear default value. + * SET: When the received PEC does not match with the PEC register content. + * @rmtoll ISR PECERR LL_I2C_IsActiveSMBusFlag_PECERR + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_PECERR(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_PECERR) == (I2C_ISR_PECERR)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of SMBus Timeout detection flag. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note RESET: Clear default value. + * SET: When a timeout or extended clock timeout occurs. + * @rmtoll ISR TIMEOUT LL_I2C_IsActiveSMBusFlag_TIMEOUT + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_TIMEOUT(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_TIMEOUT) == (I2C_ISR_TIMEOUT)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of SMBus alert flag. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note RESET: Clear default value. + * SET: When SMBus host configuration, SMBus alert enabled and + * a falling edge event occurs on SMBA pin. + * @rmtoll ISR ALERT LL_I2C_IsActiveSMBusFlag_ALERT + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_ALERT(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_ALERT) == (I2C_ISR_ALERT)) ? 1UL : 0UL); +} + +/** + * @brief Indicate the status of Bus Busy flag. + * @note RESET: Clear default value. + * SET: When a Start condition is detected. + * @rmtoll ISR BUSY LL_I2C_IsActiveFlag_BUSY + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BUSY(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->ISR, I2C_ISR_BUSY) == (I2C_ISR_BUSY)) ? 1UL : 0UL); +} + +/** + * @brief Clear Address Matched flag. + * @rmtoll ICR ADDRCF LL_I2C_ClearFlag_ADDR + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearFlag_ADDR(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->ICR, I2C_ICR_ADDRCF); +} + +/** + * @brief Clear Not Acknowledge flag. + * @rmtoll ICR NACKCF LL_I2C_ClearFlag_NACK + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearFlag_NACK(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->ICR, I2C_ICR_NACKCF); +} + +/** + * @brief Clear Stop detection flag. + * @rmtoll ICR STOPCF LL_I2C_ClearFlag_STOP + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearFlag_STOP(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->ICR, I2C_ICR_STOPCF); +} + +/** + * @brief Clear Transmit data register empty flag (TXE). + * @note This bit can be clear by software in order to flush the transmit data register (TXDR). + * @rmtoll ISR TXE LL_I2C_ClearFlag_TXE + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearFlag_TXE(I2C_TypeDef *I2Cx) +{ + WRITE_REG(I2Cx->ISR, I2C_ISR_TXE); +} + +/** + * @brief Clear Bus error flag. + * @rmtoll ICR BERRCF LL_I2C_ClearFlag_BERR + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearFlag_BERR(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->ICR, I2C_ICR_BERRCF); +} + +/** + * @brief Clear Arbitration lost flag. + * @rmtoll ICR ARLOCF LL_I2C_ClearFlag_ARLO + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearFlag_ARLO(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->ICR, I2C_ICR_ARLOCF); +} + +/** + * @brief Clear Overrun/Underrun flag. + * @rmtoll ICR OVRCF LL_I2C_ClearFlag_OVR + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearFlag_OVR(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->ICR, I2C_ICR_OVRCF); +} + +/** + * @brief Clear SMBus PEC error flag. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll ICR PECCF LL_I2C_ClearSMBusFlag_PECERR + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearSMBusFlag_PECERR(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->ICR, I2C_ICR_PECCF); +} + +/** + * @brief Clear SMBus Timeout detection flag. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll ICR TIMOUTCF LL_I2C_ClearSMBusFlag_TIMEOUT + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearSMBusFlag_TIMEOUT(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->ICR, I2C_ICR_TIMOUTCF); +} + +/** + * @brief Clear SMBus Alert flag. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll ICR ALERTCF LL_I2C_ClearSMBusFlag_ALERT + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_ClearSMBusFlag_ALERT(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->ICR, I2C_ICR_ALERTCF); +} + +/** + * @} + */ + +/** @defgroup I2C_LL_EF_Data_Management Data_Management + * @{ + */ + +/** + * @brief Enable automatic STOP condition generation (master mode). + * @note Automatic end mode : a STOP condition is automatically sent when NBYTES data are transferred. + * This bit has no effect in slave mode or when RELOAD bit is set. + * @rmtoll CR2 AUTOEND LL_I2C_EnableAutoEndMode + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableAutoEndMode(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR2, I2C_CR2_AUTOEND); +} + +/** + * @brief Disable automatic STOP condition generation (master mode). + * @note Software end mode : TC flag is set when NBYTES data are transferre, stretching SCL low. + * @rmtoll CR2 AUTOEND LL_I2C_DisableAutoEndMode + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableAutoEndMode(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR2, I2C_CR2_AUTOEND); +} + +/** + * @brief Check if automatic STOP condition is enabled or disabled. + * @rmtoll CR2 AUTOEND LL_I2C_IsEnabledAutoEndMode + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledAutoEndMode(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR2, I2C_CR2_AUTOEND) == (I2C_CR2_AUTOEND)) ? 1UL : 0UL); +} + +/** + * @brief Enable reload mode (master mode). + * @note The transfer is not completed after the NBYTES data transfer, NBYTES will be reloaded when TCR flag is set. + * @rmtoll CR2 RELOAD LL_I2C_EnableReloadMode + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableReloadMode(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR2, I2C_CR2_RELOAD); +} + +/** + * @brief Disable reload mode (master mode). + * @note The transfer is completed after the NBYTES data transfer(STOP or RESTART will follow). + * @rmtoll CR2 RELOAD LL_I2C_DisableReloadMode + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableReloadMode(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR2, I2C_CR2_RELOAD); +} + +/** + * @brief Check if reload mode is enabled or disabled. + * @rmtoll CR2 RELOAD LL_I2C_IsEnabledReloadMode + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledReloadMode(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR2, I2C_CR2_RELOAD) == (I2C_CR2_RELOAD)) ? 1UL : 0UL); +} + +/** + * @brief Configure the number of bytes for transfer. + * @note Changing these bits when START bit is set is not allowed. + * @rmtoll CR2 NBYTES LL_I2C_SetTransferSize + * @param I2Cx I2C Instance. + * @param TransferSize This parameter must be a value between Min_Data=0x00 and Max_Data=0xFF. + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetTransferSize(I2C_TypeDef *I2Cx, uint32_t TransferSize) +{ + MODIFY_REG(I2Cx->CR2, I2C_CR2_NBYTES, TransferSize << I2C_CR2_NBYTES_Pos); +} + +/** + * @brief Get the number of bytes configured for transfer. + * @rmtoll CR2 NBYTES LL_I2C_GetTransferSize + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x0 and Max_Data=0xFF + */ +__STATIC_INLINE uint32_t LL_I2C_GetTransferSize(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->CR2, I2C_CR2_NBYTES) >> I2C_CR2_NBYTES_Pos); +} + +/** + * @brief Prepare the generation of a ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte. + * @note Usage in Slave mode only. + * @rmtoll CR2 NACK LL_I2C_AcknowledgeNextData + * @param I2Cx I2C Instance. + * @param TypeAcknowledge This parameter can be one of the following values: + * @arg @ref LL_I2C_ACK + * @arg @ref LL_I2C_NACK + * @retval None + */ +__STATIC_INLINE void LL_I2C_AcknowledgeNextData(I2C_TypeDef *I2Cx, uint32_t TypeAcknowledge) +{ + MODIFY_REG(I2Cx->CR2, I2C_CR2_NACK, TypeAcknowledge); +} + +/** + * @brief Generate a START or RESTART condition + * @note The START bit can be set even if bus is BUSY or I2C is in slave mode. + * This action has no effect when RELOAD is set. + * @rmtoll CR2 START LL_I2C_GenerateStartCondition + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_GenerateStartCondition(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR2, I2C_CR2_START); +} + +/** + * @brief Generate a STOP condition after the current byte transfer (master mode). + * @rmtoll CR2 STOP LL_I2C_GenerateStopCondition + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_GenerateStopCondition(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR2, I2C_CR2_STOP); +} + +/** + * @brief Enable automatic RESTART Read request condition for 10bit address header (master mode). + * @note The master sends the complete 10bit slave address read sequence : + * Start + 2 bytes 10bit address in Write direction + Restart + first 7 bits of 10bit address in Read direction. + * @rmtoll CR2 HEAD10R LL_I2C_EnableAuto10BitRead + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableAuto10BitRead(I2C_TypeDef *I2Cx) +{ + CLEAR_BIT(I2Cx->CR2, I2C_CR2_HEAD10R); +} + +/** + * @brief Disable automatic RESTART Read request condition for 10bit address header (master mode). + * @note The master only sends the first 7 bits of 10bit address in Read direction. + * @rmtoll CR2 HEAD10R LL_I2C_DisableAuto10BitRead + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_DisableAuto10BitRead(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR2, I2C_CR2_HEAD10R); +} + +/** + * @brief Check if automatic RESTART Read request condition for 10bit address header is enabled or disabled. + * @rmtoll CR2 HEAD10R LL_I2C_IsEnabledAuto10BitRead + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledAuto10BitRead(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR2, I2C_CR2_HEAD10R) != (I2C_CR2_HEAD10R)) ? 1UL : 0UL); +} + +/** + * @brief Configure the transfer direction (master mode). + * @note Changing these bits when START bit is set is not allowed. + * @rmtoll CR2 RD_WRN LL_I2C_SetTransferRequest + * @param I2Cx I2C Instance. + * @param TransferRequest This parameter can be one of the following values: + * @arg @ref LL_I2C_REQUEST_WRITE + * @arg @ref LL_I2C_REQUEST_READ + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetTransferRequest(I2C_TypeDef *I2Cx, uint32_t TransferRequest) +{ + MODIFY_REG(I2Cx->CR2, I2C_CR2_RD_WRN, TransferRequest); +} + +/** + * @brief Get the transfer direction requested (master mode). + * @rmtoll CR2 RD_WRN LL_I2C_GetTransferRequest + * @param I2Cx I2C Instance. + * @retval Returned value can be one of the following values: + * @arg @ref LL_I2C_REQUEST_WRITE + * @arg @ref LL_I2C_REQUEST_READ + */ +__STATIC_INLINE uint32_t LL_I2C_GetTransferRequest(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->CR2, I2C_CR2_RD_WRN)); +} + +/** + * @brief Configure the slave address for transfer (master mode). + * @note Changing these bits when START bit is set is not allowed. + * @rmtoll CR2 SADD LL_I2C_SetSlaveAddr + * @param I2Cx I2C Instance. + * @param SlaveAddr This parameter must be a value between Min_Data=0x00 and Max_Data=0x3F. + * @retval None + */ +__STATIC_INLINE void LL_I2C_SetSlaveAddr(I2C_TypeDef *I2Cx, uint32_t SlaveAddr) +{ + MODIFY_REG(I2Cx->CR2, I2C_CR2_SADD, SlaveAddr); +} + +/** + * @brief Get the slave address programmed for transfer. + * @rmtoll CR2 SADD LL_I2C_GetSlaveAddr + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x0 and Max_Data=0x3F + */ +__STATIC_INLINE uint32_t LL_I2C_GetSlaveAddr(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->CR2, I2C_CR2_SADD)); +} + +/** + * @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). + * @rmtoll CR2 SADD LL_I2C_HandleTransfer\n + * CR2 ADD10 LL_I2C_HandleTransfer\n + * CR2 RD_WRN LL_I2C_HandleTransfer\n + * CR2 START LL_I2C_HandleTransfer\n + * CR2 STOP LL_I2C_HandleTransfer\n + * CR2 RELOAD LL_I2C_HandleTransfer\n + * CR2 NBYTES LL_I2C_HandleTransfer\n + * CR2 AUTOEND LL_I2C_HandleTransfer\n + * CR2 HEAD10R LL_I2C_HandleTransfer + * @param I2Cx I2C Instance. + * @param SlaveAddr Specifies the slave address to be programmed. + * @param SlaveAddrSize This parameter can be one of the following values: + * @arg @ref LL_I2C_ADDRSLAVE_7BIT + * @arg @ref LL_I2C_ADDRSLAVE_10BIT + * @param TransferSize Specifies the number of bytes to be programmed. + * This parameter must be a value between Min_Data=0 and Max_Data=255. + * @param EndMode This parameter can be one of the following values: + * @arg @ref LL_I2C_MODE_RELOAD + * @arg @ref LL_I2C_MODE_AUTOEND + * @arg @ref LL_I2C_MODE_SOFTEND + * @arg @ref LL_I2C_MODE_SMBUS_RELOAD + * @arg @ref LL_I2C_MODE_SMBUS_AUTOEND_NO_PEC + * @arg @ref LL_I2C_MODE_SMBUS_SOFTEND_NO_PEC + * @arg @ref LL_I2C_MODE_SMBUS_AUTOEND_WITH_PEC + * @arg @ref LL_I2C_MODE_SMBUS_SOFTEND_WITH_PEC + * @param Request This parameter can be one of the following values: + * @arg @ref LL_I2C_GENERATE_NOSTARTSTOP + * @arg @ref LL_I2C_GENERATE_STOP + * @arg @ref LL_I2C_GENERATE_START_READ + * @arg @ref LL_I2C_GENERATE_START_WRITE + * @arg @ref LL_I2C_GENERATE_RESTART_7BIT_READ + * @arg @ref LL_I2C_GENERATE_RESTART_7BIT_WRITE + * @arg @ref LL_I2C_GENERATE_RESTART_10BIT_READ + * @arg @ref LL_I2C_GENERATE_RESTART_10BIT_WRITE + * @retval None + */ +__STATIC_INLINE void LL_I2C_HandleTransfer(I2C_TypeDef *I2Cx, uint32_t SlaveAddr, uint32_t SlaveAddrSize, + uint32_t TransferSize, uint32_t EndMode, uint32_t Request) +{ + MODIFY_REG(I2Cx->CR2, I2C_CR2_SADD | I2C_CR2_ADD10 | (I2C_CR2_RD_WRN & (uint32_t)(Request >> (31U - I2C_CR2_RD_WRN_Pos))) | I2C_CR2_START | I2C_CR2_STOP | I2C_CR2_RELOAD | + I2C_CR2_NBYTES | I2C_CR2_AUTOEND | I2C_CR2_HEAD10R, + SlaveAddr | SlaveAddrSize | (TransferSize << I2C_CR2_NBYTES_Pos) | EndMode | Request); +} + +/** + * @brief Indicate the value of transfer direction (slave mode). + * @note RESET: Write transfer, Slave enters in receiver mode. + * SET: Read transfer, Slave enters in transmitter mode. + * @rmtoll ISR DIR LL_I2C_GetTransferDirection + * @param I2Cx I2C Instance. + * @retval Returned value can be one of the following values: + * @arg @ref LL_I2C_DIRECTION_WRITE + * @arg @ref LL_I2C_DIRECTION_READ + */ +__STATIC_INLINE uint32_t LL_I2C_GetTransferDirection(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->ISR, I2C_ISR_DIR)); +} + +/** + * @brief Return the slave matched address. + * @rmtoll ISR ADDCODE LL_I2C_GetAddressMatchCode + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x00 and Max_Data=0x3F + */ +__STATIC_INLINE uint32_t LL_I2C_GetAddressMatchCode(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->ISR, I2C_ISR_ADDCODE) >> I2C_ISR_ADDCODE_Pos << 1); +} + +/** + * @brief Enable internal comparison of the SMBus Packet Error byte (transmission or reception mode). + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @note This feature is cleared by hardware when the PEC byte is transferred, or when a STOP condition or an Address Matched is received. + * This bit has no effect when RELOAD bit is set. + * This bit has no effect in device mode when SBC bit is not set. + * @rmtoll CR2 PECBYTE LL_I2C_EnableSMBusPECCompare + * @param I2Cx I2C Instance. + * @retval None + */ +__STATIC_INLINE void LL_I2C_EnableSMBusPECCompare(I2C_TypeDef *I2Cx) +{ + SET_BIT(I2Cx->CR2, I2C_CR2_PECBYTE); +} + +/** + * @brief Check if the SMBus Packet Error byte internal comparison is requested or not. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll CR2 PECBYTE LL_I2C_IsEnabledSMBusPECCompare + * @param I2Cx I2C Instance. + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPECCompare(I2C_TypeDef *I2Cx) +{ + return ((READ_BIT(I2Cx->CR2, I2C_CR2_PECBYTE) == (I2C_CR2_PECBYTE)) ? 1UL : 0UL); +} + +/** + * @brief Get the SMBus Packet Error byte calculated. + * @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not + * SMBus feature is supported by the I2Cx Instance. + * @rmtoll PECR PEC LL_I2C_GetSMBusPEC + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x00 and Max_Data=0xFF +*/ +__STATIC_INLINE uint32_t LL_I2C_GetSMBusPEC(I2C_TypeDef *I2Cx) +{ + return (uint32_t)(READ_BIT(I2Cx->PECR, I2C_PECR_PEC)); +} + +/** + * @brief Read Receive Data register. + * @rmtoll RXDR RXDATA LL_I2C_ReceiveData8 + * @param I2Cx I2C Instance. + * @retval Value between Min_Data=0x00 and Max_Data=0xFF + */ +__STATIC_INLINE uint8_t LL_I2C_ReceiveData8(I2C_TypeDef *I2Cx) +{ + return (uint8_t)(READ_BIT(I2Cx->RXDR, I2C_RXDR_RXDATA)); +} + +/** + * @brief Write in Transmit Data Register . + * @rmtoll TXDR TXDATA LL_I2C_TransmitData8 + * @param I2Cx I2C Instance. + * @param Data Value between Min_Data=0x00 and Max_Data=0xFF + * @retval None + */ +__STATIC_INLINE void LL_I2C_TransmitData8(I2C_TypeDef *I2Cx, uint8_t Data) +{ + WRITE_REG(I2Cx->TXDR, Data); +} + +/** + * @} + */ + +#if defined(USE_FULL_LL_DRIVER) +/** @defgroup I2C_LL_EF_Init Initialization and de-initialization functions + * @{ + */ + +ErrorStatus LL_I2C_Init(I2C_TypeDef *I2Cx, LL_I2C_InitTypeDef *I2C_InitStruct); +ErrorStatus LL_I2C_DeInit(I2C_TypeDef *I2Cx); +void LL_I2C_StructInit(LL_I2C_InitTypeDef *I2C_InitStruct); + + +/** + * @} + */ +#endif /* USE_FULL_LL_DRIVER */ + +/** + * @} + */ + +/** + * @} + */ + +#endif /* I2C1 || I2C2 */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* STM32F0xx_LL_I2C_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit