diff options
Diffstat (limited to 'content/projects')
| -rw-r--r-- | content/projects/8seg/index.rst | 215 |
1 files changed, 29 insertions, 186 deletions
diff --git a/content/projects/8seg/index.rst b/content/projects/8seg/index.rst index ebf9070..38a00bc 100644 --- a/content/projects/8seg/index.rst +++ b/content/projects/8seg/index.rst @@ -4,207 +4,50 @@ external_links: - name: Sources and hardware design files url: "https://git.jaseg.de/8seg.git" - name: Web interface at 37C3 (congress network only!) - url: "https://8seg.jaseg.de/ + url: "https://8seg.jaseg.de/" + - name: Technical overview blog post + url: "/blog/8seg" + - name: Contact email + url: "mailto:8seg.m@jaseg.de" summary: > 8seg is an experimental textual display. It is made from a 45m by 1.5m large lacework banner that can be put up in a variety of spaces, conforming to the space's size and shape through bending and folding. --- -8seg Technical Overview -======================= +8seg +==== -Prologue --------- +8seg is an experimental textual display. It is made from a 45m by 1.5m large lacework banner that can be put up in a +variety of spaces, conforming to the space's size and shape through bending and folding. -German hacker culture has this intense love for things that light up in colorful ways. Like for many others in this -community, I have always been fascinated by LEDs. One of the first things on my pile of unfinished projects was to build -my own LED matrix and use it to display text. When I started that project, I was still new to electronics. Back then, -commercial LED matrices were limited to red or green color only, and were very expensive, so there was an incentive to -build your own. At the same time, while individual LEDs were'nt expensive anymore, they hadn't started to be cheap yet, -either. On top of the material cost, back then there were no PCB fabs, and especially no PCB assembly houses that a -hobbyist could afford. Ultimately, I ended up never finishing this project because I felt it was more of a feat of -material wealth than of technical prowess. +8seg is currently being set up at 37C3 in the entrance hall, on the second-floor railing in front of Hall X. -Over time, LEDs came down in price, and peoople started using them in all sorts of fun things. Around the mid-2010s, -cheap-ish, ready-made tapes and chains of RGB LEDs that included WS2811 or similar digitally controllable driver chips -led to a cambrian explosion in projects involving large amounds of colorful LEDs since suddenly, all you needed was an -arduino and a beefy power supply to individually control an almost unlimited number of these LEDs. +Posting messages +---------------- -Today, LED technology has advanced even furhter, to a point where now you can buy staggering quantities of the second -generation of these controllable LEDs that provides better color rendering embedded in all sorts of shapes, from tapes -through rings to grids. When I built the first matelight_ in 2013, the matelight's 640 individually-controllable LEDs -were *a lot*. Today, you can buy a roll with several thousand channels for about the price of a nice pizza. +To send messages to the display, please use the web interface linked above. -The idea behind 8seg --------------------- +8seg is a community service run by a sole volunteer. Please respect my work, and please do not post offensive messages, +spam or similar. 8seg is currently open to the congress network on the hope that y'all will behave civilly. Please don't +make me put a login wall in front of this thing, alright? ;) -Living through this amazing escalation of LED technology, in 2018, I looked at a then-obsolete piece of single-color, -dumb, non-controllable LED tape with a simple question in mind: Taking this unsophisticated artifact of yesterday's -technology, what would be the coolest thing I could build from it? Can I buld something that not only rivals, but -outmatches the modern controllable LED stuff? From that question, I set myself two goals. First, I wanted to keep the -project's use of financial and labor resources reasonable. A lot of art consists of taking a simple idea, and simply -extrapolating its implementation to a ridiculous scale at the expense of the artist's time and wallet. That wasn't the -point I wanted to make. I wanted to make something cool from an obsolete technology, not prove how much patience I had -soldering. My second goal was to create something that is meaningfully controllable. Controllability is much harder with -these dumb LED tapes, but it is possible nontheless, and I wanted to test out how far you could go with it. +You may write code to talk to the web interface, but please do not post automated messages at a frequency higher than +one per 20 minutes. No spam, no commercial advertising and absolutely nothing cryptocurrency-related. -After thinking through a number of possibilities, I settled on the basics of the 8seg design I ended up realizing. The -installation would be a banner-style display consisting of a series of characters made from non-controllable LED tape. -The banner can be rigged up in any convenient air space, bending and folding to conform to the space's shape and size. -The key idea behind 8seg is that it makes up for it's lack of control fidelity with sheer size. If nothing else, this -non-controllable LED tape is *cheap*. +Scheduling regular messages +--------------------------- -The design of a single 8seg character -------------------------------------- +If you want your message to be added to the regular "idle rotation" of 8seg, which the display cycles through when no +other messages are queued, please email me at the contact email above. -Each 8seg character consists of 8 *segments* of LED tape that are inter-connected through small circuit boards, four in -the corners, and one in the center. As it turns out, 8 segments arranged in this shape are enough to display all of the -English language's alphabet as well as numbers in a weird, but readable form. +Reporting abuse +--------------- -The electrical design of an 8seg character has one weird trick at its core. To avoid having to run a bunch of wires from -some kind of driver circuit board to each of the eight segments, I thought, why not use the LED tape itself instead for -power and data transmission? Wires are heavy, expensive, and annoying to solder, so if I could find a way to -interconnect the LED tape so that it can all be driven from a driver circuit located at one of the character's -junctions while simultaneously powering that driver circuit, an 8seg character wouldn't need any wires at all anymore. +If you see 8seg being used for something stupid or bad, please email me at the contact email above. -8seg achieves this feat using a circuit as shown in the diagram below. Interconnections between the LED tape segments -are done with a small circuit board in each of the four corners. The design is rotationally symmetric, and all four of -these boards are identicaly. The top right and bottom left corners simply use the back side of the same circuit board -used in the top left and bottom right corners. +Further questions +----------------- -.. image:: 8seg-circuit.svg - -The driver circuit sits at the center of the character and directly connects to the four diagonal segments. The key -thought behind 8seg's driving scheme is that there are two common phases wound through the display in a zig-zag pattern -as shown in red and blue in the schema below. These phases alternate their polarity at a high frequency. Each segment -has its negative pole connected to one of these two phases, and can be turned on by the driver while that phase is low -and the other phase is high. While a phase is high, the LEDs on all segments connected to that phase are reverse-biased, -and thus these segments remain dark. - -The positive poles of all segments are connected to the driver circuit in the center through a spiral pattern. Each arm -of the spiral is made up of two segments, one diagonal on the inside, and one horizontal or vertical on the outside. -The two segments on each spiral arm are on different phases, one on each of the two phases. Thus, during a single cycle -of the two phases alternating polarity, first one of the two segments has its polarity the right way around, then the -other. The driver can turn on the active segment by connecting the spiral control line to the positive LED supply -voltage. - -Both phases cross at the center where the driver circuit is located, so the driver can power itself from the two phases -using a simple full bridge rectifier. - -Saving copper with point of load regulation -------------------------------------------- - -In the beginning, I experimented with the design above, putting 12V AC on the two phases, and letting the driver switch -its derived LED supply using some cheap MOSFETs. This simple design totally works, but it has an important shortcoming. - -8seg is designed to be physically *very* large. This means that not only does it have a large number of LEDs that -together need a lot of current, it also has to transmit all of that current across significant physical distances. The -consequence of this was that in the initial design, I was looking at either needing hundreds of Euros worth of copper -cables, or burning hundreds of Watts of electricity into heat if I were to use thinner cables. In this case, cables act -like resistors. In a resistor, power dissipation rises with the square of the current inside the cable. This is bad for -8seg since it means halving the amount of copper in those wires increases power dissipation in these wires fourfold. - -Despite that downside, this square law does come with an upside, too. If we assume we have wires of a particular fixed -diameter, if we can halve the current through those wires, we can quarter the wires' power dissipation. If we want to -deliver the same amount of power to the LEDs as before, to halve wire current, we have to double the voltage, and add -some circuitry on the drivers to convert that increased voltage back down to close to our LED tape's nominal 12V. - -Alas, simply doubling the voltage leads to one question: How is it that we can pass double the voltage through our LED -tape to the center control circuit? Isn't the LED tape made for 12V operation only, not 24V? The answer to this -apparent problem is that the center is connected to the AC bus voltage only through the negative side of the LED tapes, -and controls their positive sides to turn them on or off. The AC bus voltage never appears directly across any single of -the eight segments. At the same time, a simple buck converter stepping down our new 24V bus voltage to 12V, and feeding -the segment control transistors with that instead of feeding them straight from the rectified AC bus allows us to feed -the segments with 12V. The only difference between this circuit and the straight 12V variant is that now, during OFF -times, the LED tapes see a negative 24 v across them. To make sure that's not a problem, I tested a number of them with -different LED colors and from different manufacturers, and all of them held up past the 50 V I could easily generate -with my lab power supply. - -Synchronous rectification -------------------------- - -I implemented the point-of-load regulation in a new revision of the center circuit, and built a prototype digit. When I -tested this prototype, to my dismay, I noticed some really strange behavior. In my tests, the LED tape did not properly -light up, and when I checked the voltages with my oscilloscope, I noticed that the center circuit's ground was floating -several volts *below* the AC bus voltage's negative phase. How come? - -After some head-scratching, I found that this problem was due to a simple instance of Kirchhoff's current law. Consider -the point where the AC bus voltage's currently negative phase enters the center circuit board. Let's say that we -dissipate 24 Watts in the segments' LEDs. In this case, at 24 Volts, 1 Ampère will flow into the center circuit's -terminal connected to the currently positive phase, and out from the center circuit's terminal connected to the -currently negative phase. - -Now consider the current through the LED tape. During one half-cycle of the AC bus, the center circuit can only address -the four segments that have their negative rail connected to the currently negative phase of the AC bus. If one of these -four segments is currently on and dissipating our 24 Watts, that segment will be fed 2 Ampère of current from the center -circuit through its positive rail. My mistake was that I did not consider what happened to the return current here. -The corresponding 2 Ampère return current of course flows back through the segment's negative rail into the center -circuit, and herein lies the issue: That negative rail is where our center circuit's supply current comes from! This -means that according to Kirchhoff's current law, the 1 A flowing out from the center circuit at its input are adding up -with the 2 A flowing into it. The result of this is that in the currently positive phase's connection, we get 1 A -flowing into the center circuit, while in the negative phase connection, we get (-1) + (+2) resulting in another 1 A -flowing into it! The only terminal where current flows *out* of the center circuit is the positive terminal connected to -the active segment, out of which 2 A of current are flowing. - -The big problem with this confusing scenario is that this means the bridge recitifier in our center circuit cannot work, -since its negative-side diodes are reverse biased while any of the segments are on. We can't just add more diodes here, -since that would just short both AC bus rails together. Instead, the solution is to add one rather chonky MOSFET in -parallel with each of the two negative-side diodes of the bridge rectifier that are controlled by the center circuit to -act as a sort of synchronous rectifier. When we turn on one of the segments, we have to turn on the MOSFET on the -currently negative rail to allow the segment's return current to bypass the bridge rectifier's negative-side diode. Fun -fact: If we turn on the wrong MOSFET out of the pair, we short the AC bus, resulting in a very quick end of life for that -poor MOSFET. - -Power line data communication ------------------------------ - -As we saw above, the driver providing power to a string of digits has to continuously alternate the polarity of its -output voltage to provide one part of the digit circuits' multiplexing. Since we want to provide the control information -to the center circuits through those same two wires, we can choose between a number of viable power line communication -schemes. These schemes usually require a beefy transmitter adding a modulation at a frequency much larger than the -underlying bus frequency, and a filter circuit at each receiver to filter that signal from the much stronger fundamental -AC waveform. In our application, I saw two issues with these classical approaches. First, they require fairly complex -circuitry, especially the beefy transmitter at the driver. Second, they are susceptible to attenuation with either -changing load or over long distances, which could potentially be a problem with the high currents and long(ish) wiring -runs 8seg needs. - -Because of these disadvantages, I decided on another approach entirely. Instead of modulating our control signal on top -of the AC power waveform, we modulate our control data *into* the AC power waveform. To not interfere with the display -and cause outages or flicker, and to avoid having to blank the display during transmissions, we choose a modulating -technique that leaves the proportions of negative and positive half-waves undisturbed. The practical realization of this -is that instead of alternating positive and negative half-waves, we send a positive half wave for each "one" bit, and a -negative half wave for each "zero" bit, effectively creating a phase shift keyed signal with two states with an -180-degree phase shift, with the transmitted bit rate synchronized to twice the underlying carrier frequency. - -The remaining question is how one can encode arbitrary binary data into a continuous stream of ones and zeros that is -precisely 50 % ones and 50 % zeros across any time span longer than a few dozen bits. There exists a near-optimal -solution to this question from ethernet over copper twisted pairs. In ethernet, the encoded and modulated signal passes -through an isolation transformer to protect the ethernet transceiver from interference or dangerous voltages coming in -through the ethernet port. For this isolation transformer to work, the modulated ethernet signal must be exactly -balanced to avoid saturating the transformer's core with a DC offset. Ethernet solves this issue by using an encoding -known as `8b/10b encoding`_. 8b/10b encoding is named like that because it specifies a way to produce a 10 bit codeword -from any 8 bit input data word while guaranteeing that the resulting codewords are always precisely balanced when -looking at two or more consecutively. - -Framing -------- - -Since 8b/10b encoding maps a space of 256 data words to 1024 code words, there necessarily are a number of unused code -words. While for some of them, leaving them unallocated is beneficial because it improves error tolerance by decreasing -the probability of one code word turning into another undetectably when a single one of its bits is flipped, even -accounting for that it leaves some room for other uses. In 8b/10b, these leftover code words are used for synchronizing -the receiver to the transmitter, and for framing transmissions. Synchronization is necessary for the receiver to know -where a code word stards, and 8b/10b has a handful of special "comma" code words that can be uniquely identified in a -continuous stream of received ones and zeros, because no other combination of 8b/10b code words could produce the same -sequence of ones and zeros of the comma code word anywhere. - -The leftover code words that are not commas are useful, too. They can be used, for instance, as filler code words -betwene actual data transmissions, or to act as framing markers denoting things like the end of a protocol message. - -The 8seg driver produces its modulation waveform by translating all data to be transmitted into 8b/10b codes, padding -the result with framing markers and filler codes, and copy-pasting together the corresponding AC waveform from a small -set of pre-programmed waveform transitions. - -.. _matelight: https://github.com/jaseg/matelight -.. _`8b/10b encoding`: https://en.wikipedia.org/wiki/8b/10b_encoding +For further questions, please email me at the email linked above, or message me on mastodon at `chaos.social/@jaseg +<https://chaos.social/@jaseg>`__. |